fe600

Hello, I am a proud new owner of a FE600 1997 (without electric starter). Unfortunately I have some questions about my new ride that I cant answer myself. 1. It doesn’t have a manual decomp. Should it have one? The previous owner told me that it has a full automatic decomp but since...

I found some excel wheels for sale off of a 1999 501 and would like to have a spare set for quick tire changes from street to dirt for my '99 FE600E :? Will these be a direct fit or do I need to modify them some how? Or if anyone has a wheel set for sale that will fit. Thanks Tom

hey,I have a 94 fe 600 which when riding, began revving up, as if in neutral or there was no load on the engine, this happend very abruptly and would fall back into gear, or regain drive, when the revs dropped very low, this only happend in 3rd gear upwards and got progressively worse until...

HI there i have a fe600 1998 bottom end and also a 1997 fc600 are the cranks and other parts interchangable as the fc ble wina big way rod big end and piston gone? thanks

How can i reset my ignition timing. the engine is rebuild, the only thing i stil need to do is reset the ignition timing

While repairing an oil leak from the starter o-ring I noticed 2 teeth missing on the larger cog of the Gearwheel Starter/Balancer. The larger cog is about 5cm in Diameter. I have been quoted $350 AUD for the part and a 6 to 8 week wait. Seems very expensive and even the dealer was surprised...

Hi, I have searched the forums a lot and haven't quite found what I am looking for, so I thought I would ask :) . I have a 1997 electric start husaberg fe600. I have just given it a complete engine rebuild and the marks I made to rebuild it as I took it apart have rubbed off so I am completely...

What are the issues i'd run into mounting supermoto wheels from the 600 to the 501e? I know the axles are the same, but how does swingarm width, the upsidedown forks etc screw with things? Thanks for your help in advance!!

Thanks for your help again, it's running :D Now some questions about truning it into SM 1. Has someone of you an adapter for 320mm Brake disk 2. Has anybody a rear sm rim 17" 4,25 wide and 36 holes for Talon ... or best a complete rear wheel must'nt be with talon. For this time...

My 2000 FE600 starts fine (kick) cold with the choke on - 2nd or 3rd kick. Its ok hot sometimes. It was a problem hot but I found if I switched the fuel off before the engine it started ok - on investigation I found one float full of fuel..replaced it..needle & seat seemed ok > that improved...

Please help! I have been a big bore rider for years but always 2-stroke. I have just purchased a 97 600 E that has only been rode twice and sitting for 2 years without being started. I have already completely serviced the bike and it seems to be running fat. A little smoke (black) even at idle...

hello all still cant get my 600 to tick over smoothly cleaned carb but is still not right it's ok while the chokes on witch is stupid cos on mine it's either on or off no half choke so when i think the bikes ready to turn off the choke it just dies turn up the idle speed & it runs to fast cant...

so is it true that the older 600 engine has the highest output of them all does anyone know the true output at the backwheel standard that is ????

I bought my FE600 3 years ago. It has always ran great except for this problem. It starts on the first or second kick cold and first kick hot. It idles perfect. It runs great 50% of the time, but the other 50% it dies just as you turn the throttle from idle. It will even try to die when...

Has any one done any modifications to the fe600 electric start, front forks. The springs seem way soft, yet do not use more than 8 inches of travel. A couple of riders with the same bikes have the same problem. Soft springs they seem, need pre-loading yet not all travel used. No more than 9...

can any one show me a link or have put there 600 on a dyno want to know how much power this beast makes cheers doug