fe600

Hi Guys, Need some advice on possible fix. Rode my 99 FE 600 today, Has new plug, clean left air filter, top filter basically blocked off waiting on replacement, New 98 oct fuel. Kick starts easy without the choke. Idles nicely, runs well when you don't rev it much and use the torque to push...

will a 501 starter idler gear work in a 600 fe?

I found a motor but it's a older one, it has a screw on oil filter cover so it might be 90-96 ? does any one know. I have a 97 with a oil pump and this one does not, will the crank shaft work in my motor ? Brian

1998 FE600E wi $2100 Howdy, clean/clear title, owned the bike for 9 years but have hardly ridden it. Previous owner lowered the forks so it has a 34" seat height. Have held onto it for a sort of spare, would like for someone to enjoy this ride. $2100 in Janesville, WI Have a whole foot...

Hello guys! I've recently bought a FE 600 2000 street legal supermoto. When i bought it started and ran great, but when i rode it a little a couple of days ago and stopped it did not start again. The spark plug gets wet so it gets gas, and when i pulled the spark plug out and tested it...

Hi, I have a old 1993 Fe600 and i was thinking of getting a electric start to this, but i'm not even sure if its possible? Are there anyone out there that might have done this mod, or have any tips and tricks? Thanks in advance!

Hi, My first post here, i recently got a hold of a old gal, a FE600 from 93, and it seems that the headgasket did sprung a leak... So i was thinking why not tear the engine down and replace all the gaskets and just a overhaul of it. BUT i cannot find a gasket kit for a 1993, how does the...

Hello, Anyone know how to remove the battery from a 2000 FE600E so I can install a new one?? I can not figure out how you are supposed to remove the battery? There doesn't seem to be room to get it out? Will I have to remove the shock or somthing? I can't beleave they would make it so difficult...

Greetings Husaberg.org! Thanks for the warm welcome to the forum. I recently picked up a pair of 2000 FE600E 's off of Craigslist and the previous owner told me to check you guys out. I've spent the past couple days looking thru the forums, there appears to be a wealth of knowledge here! I...

Hello, Up for sale is a 2000 fe600e. Bike runs strong!bought it thinking I would start a supermoto project, but unfortunately have to many projects going at once and need the garage space. 100% stock. Never wrenched on from what I was told/can tell. Street legal and plated in california, USA...

Hi all, I have a WP Extreme fork from a Fe600 (might from 1998, not sure) that I will install on a Suzuki DR800 It came with wheel axle and 2 spacers on it, one steel and one aluminium, similiar thickness, same i.d. My axle is 17mm Now I need to buy front wheel and caliper/bracket as...

What is the maximum rev that you shouldn't go over on those engines? Mine is a 1994 600cc with no oil pump. And what temperature is dangerously high? Otherwise, just got the bike running and it's finally easy to start hot and cold. Just installed a trail tech speedo/tach, horn, brake...

I'm looking for a chain slide for my 1998 FE600 Elduro. Any help would be greatly appreciated.

My 94 600 is hard to start so I thought I should try and install a CD1 jet inside the pilot since my bike didn't have this. If you have the CD1 jet inside the pilot jet, how far in should it go? All the way until it seats? My bike is kickstart only.

I have a great 1995 FE600 I would like to sell or part out. I made the mistake of not changing the oil after 2 rides to the desert and took it out for the third trip and grenaded the rod bearing. otherwise a great bike.

With no history on the bike except that it's a bit hard to start and with an upcoming tear down/status check I have the following questions: 1. I have read here that the cam follower bearings often go bad and should be replaced periodically. Is it enough to inspect them or should they be...

Good afternoon my friends! I'm writing to ask about something. I have an Mikuni Corp 40 carburetor in my husaberg fe600, im going to buy FCR39, Mikuni is propably one of the problems with my husaberg. Everyday i have to kick it few times <in good moments, generaly it take 10-15 mins - hundreds...

Hi guys! Im writing to you to ask about one thing, will the gearbox from Husaberg FE501 fit to my 2000 FE600? I have 6 gears, the 501 too, but im little bit scared about engine, it has any things which are different? I had a little bit problem, cause i had an old gearbox from FE600 without oil...

New old member, with a new old FE600:) It`s a 2000 m/y, with very little known history, but works just fine. Well, almost... The clutch is dragging ever so slightly; not enough for the bike to creep forward, but it certainly puts up a fight if I try to pull the bike rearwards (first gear...

Hello all! I am starting a new project (custom build) and would need a few measurements of husaberg 600cc engine. My plan is to use old (no oil pump and no electric starter) engine, but i don't have it jet, and i have to check if it will fit. Would someone be so kind and take few measurements...