fe350

c/s seal # 35000201 for a 93 fe350 is no longer available 28x35x4 where can I buy one? Also c/s spacer #24002001 NLA. Any Ideas?

I have always been a fan of the Bergs since watching team Surdyke run the Flat River Grand Prix in the early-mid 90s.(south of St. Louis MO) I saw an older (95-96) FE350 on Craigslist needing motor work & when the $ dropped to $250 I decided to take a chance on it. Expecting the worst, but...

I arrived home from work today to find a heavy postage pack in my mailbox. Felt to be about the right weight of a brand new used stator and coil. I don't even know if I said hi to my wife as I headed trough the house and into the garage. Did a quick ohm check, and tossed it all in. Held the...

Hi - Here with more questions. Please take pity upon me, I'm not a motorcycle mechanic. Now I have two stators for my bike. For the black to red reading I get 1070 and the black to green reading I get 23. With the other, I get 1526 for the black to red and 49.3 for the black to green. Which of...

Hello This is my first visit on this forum. I was referred here by a Husaberg dealer. Any help I can get is greatly appreciated. So here we go - I just purchased a 1996 FE350. I was told the stator was probably bad, but I think I got a fair deal on the bike so I went ahead and bought it. Now...

Hi everyone! I have just obtained a 96 fe350 basket case. The po didn't know much about the bike and said that it needed a crank. The engine has compression and kicks through with no abnormal resistance or sounds, so I'm wondering if their is a way to determine if the crank is bad without...

I'm starting to get used to my freshly rebuilt '94 FE350. I have put a lot of time on it clearing trails, where I'll ride a while, and then get off and cut limbs & vines for a while, but it's Husqvarna clutch keeps it from being a really good "finish" trail working bike (putting up and taking...

Hi there - Great site and content By way of introduction, I am from Auckland New Zealand, and being a 40's something, have a bit of a passion for 80's era mx/enduro bikes. I have a restored 1989 ATK 250 and 1987 Cagiva WMX 250 from this era of experiment and new technology, a white knuckle...

I apologize if this is readily available information here, but I first did a search on the FE350, another on the posts pertaining to top end reassembly, and thoroughly searched the available downloads here (after downloading all the workshop manuals listed). Right after I got the FE350, the...

well my 400fe 2002 is gone due to money issues. I found a 350, all electrics are new, FCR installed, and much more. I'll tell you the price when I know, but that is not my question. I want to know is there was something wrong with that bike. Should I take it? Will it work forever or I'll have to...

Hey every one, my dad is looking at getting a 95 Fe350 for my brother. I was wondering if any one new much about the bikes such as any problems or bad designs. thanks

I got the 92 fe350 going tonight I had to put a new stator in but it runs now. When I got this the stator had been removed I can not figure out the wiring on the lights. It had seven wires how do I hook up the lights it has two yellow and one blue wires left over but I cannot figure where they...

[ I just got ahold of a 96 FE 350 Husaberg and am looking to get this beauty back in top shape. The carb runs gas through it like a baby crying and will only stop after I have had the fuel shutoff off for awhile. I have read that the floats tend to absorb the gas and become"heavy"after a few...

Got a -93 FE350 (Yes I know it is old). Brembo brakes. It desperately needs new pads but I just cant get the safety pin out. It rotates and moves slightly from side to side, but not out... What do I do wrong? Is there a friction lock and I should get the C-clamp out? Thanks!

Help! I need to change the oil in these forks and have no idea where to start. There is a clicker on the top of the forks and a bolt in the bottom. Can anyone tell me if the bolt at the bottom can be taken out to change fork oil? Thanks!

Hi, Any tips on locating the source of oil causing my '96 FE350 to smoke? It is enough smoke to signal a problem but not an embarrassing amount. Here are some facts: -replaced piston and rings -honed cylinder quickly at the time of the new piston install -smokes only after the bike is at...

Unfortunately, I am not in any manual that I have access to. Any help as to what I should have stock would be much appreciated. I am just about to go out and pull the carb off to find out for myself. Gonna check float level. Will update with results. PS- Runs good, but runs a bit rich...

I have invested in a Husky FE350 1992 and would like to get hold of manuals och tech instructions for fork oil change. I Understand that it is a upside-down WP 295mm front fork but would like to know if there is a WP model for it? At KTM there is a posibility to download the manuals for WP...