cylinder

Hello, I picked up up a project 07 fe550, it started burning oil on the PO, he took it apart and there it sat. From what I can tell something scratched the cylinder, causing a lot of blow by or oil getting passed the rings. The weird thing is the valves look just fine, and so does the...

Hello Husaberg community! My name is Tristan and I am from Washington State, USA. I have a 2003 FE501 that I bought a little over a year ago with ~50 hours on the clock. I put about 10 hours on the bike and it ran decently, but while jetting/tuning the carb I was doing repeated WOT runs and she...

I finally got all my parts back from various places for my 2000 FC 501. I don't have a piston ring install tool. So I tried the following being very careful, but gave up right away before I had done any damage. Maybe I could have done it the opposite way, but that's not what I did. So I...

What is the thickness of the cylinder holder of husaberg 2003 400 fe, it tip below 0.1 tenth of the bike's spore so it is that you had water leakage by Someone has already rectified the cylinder block

Hi for sale used cylinder the had tell me what's not similar with mine engine FS650 2003 model so for this need to sale its in good condition maybe someone needs

I have a 2009 Husaberg FE570 which has a bore of 100mm and stroke of 72mm. I have found that a KTM 500EXC has a bore of 95mm (same as Husaberg FE 450) and stroke of 72mm (same as FE570) with the same compression ratio of 11.8:1. My question is: will the KTM cylinder fit on the Husaberg so I can...

Good day guys: Husaberg 390 loosing mineral oil into engine after it sits for a week or more, I'm sure it will get worse in time. Does anyone have a part number for the seal on the oem slave cylinder ? or a recommended fix besides replacing the complete slave cylinder? thanks

My cylinder is well assembled, the bikes 400 Fe 2003 does not have any brand to run the cylinder, is closed and is losing water , I think it is very strange someone can tell me what is passing the joint is original Husaberg , the cylinder must be bad :eek:

Hi Guys, Well i discovered that the strange things my clutch was doing is because the master cylinder bore has some of the anodising flaking off. This is allowing fluid to leak past the piston as well as wearing out the piston seal. Short of replacing the whole clutch master has anyone had a...

What is your favorite rear master cylinder guard?

https://imgur.com/a/1nfo196 - picture of the sleeve. So I was taking the cylinder head off to renew my valve springs when I noticed that there was small nodge on top of the cylinder. Further investigation revealed that the whole top of the cylinder sleeve had been cracked clean off. In the...

Hi guys my I need a new cylinder for my 1998 husaberg fe 501, I try to find one online and nothing if someone can tell me where to look it will be really aprreciate

Hi Guy I have a 1998 husaberg fe 501 I'm pretty sur I jump the cylinder last season that few month I try to find a new cylinder and piston for it and I don't find nothing can somebody help me and I'm looking for the repair manual to thank

Hi, I own 2010 FE390 (70degree) and am in the middle of checking the valve clearances. I used a narrow cylindrical watercolour wooden paintbrush with the handle down to check TDC via the spark-plug hole while lining up the two marks on the cam chain sprocket. I've done this for years...

Hi all, Has anyone done a rebuild on the master cylinder on the FS, separate fluid resivouir. Where do you get parts? I have tried munn racing been good in the past with the parts fiche but they dont seem to do husabergs any more? Also how do you get the piston out of the housing? There...

Hello to all! Again, I ask for help. Whether prompt there are differences in a head of a tselindra and a valve of a cover of model 400 from 501 motors till 1999. and whether it is possible to put the head from 501 to 400.

WANTED!! Looking for Front HAND BRAKE CYLINDER Hello I am looking for a HAND BRAKE CYLINDER Part number 77013001144 If anyone has one they would like to part with I would love to take it off your hands. Of course it has to function right and be in good condition. Thanks -DaBergman

Ok hi guys, I did an oil change on my burg it's a fe 450 and i pulled the screen out of the banjo bolt at the top of the engine and now can't remember which way it goes in. The screen is only open one end. Cheers in advance. Sent from my SM-G930F using Tapatalk

Has anyone have a 570 cylinder the want to sell? A complete motor would be great if not too expensive.

needed clutch output cylinder location brisbane au,2006 550fe .have found one !