camshaft

Does anyone have a lightly used camshaft they'll sell? I need a camshaft for a 2010 FE450. I could also use FX450 or FE570 cam if available.. You can message me at [email protected] Thanks!

My cam got damaged because the intake rocker arm bearing can someone help me with the part number of the KTM camshaft that will fit to my 2004 Husaberg? i may not need high torque.... even 10-15 kw less for my weight are ok, maybe a cam from KTM400 Can I change the damaged rocker small...

Hi! Is the camshaft for FE and FC model the same? Someone know if this camshaft is FC or FE?

I bought recently this FE450 2004 . Very hard to start when hot ,also in cold condition seems much compression. i opened the camshaft cover for inspection. I found the play of tappets for exhaust over 1 mm play ...( yes 1 mm, right ) , The intake tappets space were around the recomandation...

Hi, I'm looking for new camshaft bearings for my FS650e 05. What is a good choise? Thanks

Hello, want to buy the LRX1 Racing Cam. Please make offers. regards

Anyone have experience with 08 camshaft and dellorto carb jet sizes? Please let me know! Thank you!

Any expirience Taffmeisters Modified CAMSHAFT

does somebody know what cam came in the 99 fx 600?

Hi Everyone, I have a question about camshafts, i found a post where somebody said that 08 camshaft for fs 650 2002 is better power on high rpms, and with 53 (original) camshaft the bike have a big torque at low rpm but wont enough in high rpm. What is the better for longer runing hours...

Hello! I have a 2001 FC470, which I recently picked up.This bike does not appear to have been used more than 30-40 hours total. 8 years ago new crank bearings and 2 balance weight bearings were installed. The camchain made a slapping noise when kicking over and there was no spark. New stator...

hello.I'm new here and my English is not exactly good.sorry:D I have a problem with my husaberg fc 550 2005 4-speed.Problem is in roken rocking arm for intake valves and damaged camshaf.In our country (Slovenija) is impossible to find parts for husaberg.Or maybe someone knows if spare parts are...

Husaberg 04 650fs Cam for 644cc As I believe same up to 05-06 ? Motors Just seeing wats out there see who has one in stock by any chance please As have been told pple used ktm 525 cam cut pump shaft off works fine (option on the table) Non available in Australia as I'm wear of...

G'day all, I have a FX450 '10 that I'm using for motard around local tracks. I have been running the Vortex ECU, straight through muffler and cut back the seat to derestrict the air filter. This has really livened up the 450, but, a mates stock FC450 Husky (around '13) has the edge on...

I currently have a 1995 FE 501. Can I use a 1997 FE 501 camshaft with the auto decompression in the 1995 head? If this is possible, should i disconnect the cable from the kickstarter and let the auto decompression on the cam do it's job? All input is appreciated!

Hi! I have pressed in new bearings on the camshaft on my 650 Berg. I read somewhere in the manual that the bearing should be pressed in so you just got a little clearance between the bearing and the auto decomp device. But I cant find any information on how far pressed in the other bearing...

Hello! I am Finnish and I'm new to buck . I'm sorry for the bad English language I need the cam shaft and the rocker arm exhaust side. Make me a private message if you have to sell parts to me , and you can send them to me in Finland Where should new ? or better parts to replace the...

Any of you guys have one laying around collecting dust you'd care to part with? Could use a kickstand as well. Thanks! Bruce

hello guys!!! i need camshaft for my berg! my question is...can i put camshaft from 501(01,02,03) or 550 in my 450 cylinder head???I will appreciate your help! !!

Husaberg Camshaft Profile Tool Dale