broken

Hello, I need some input on how to replace a broken tappet screw. Any help would be greatly appreciated! Is there an easy way or do I have to pull the head?

hi guys, i have an 08 fe450e. I've a broken intake valve spring, later on in the week ill be pulling the head to inspect the guide and seat and make sure the piston hasnt kissed the valve too hard if at all. I have some compression but not much, and the bike doesnt run. i am upgrading to a dvsk...

A few days ago after about a 45 minutes trail ride I noticed my left leg was getting VERY hot. Made it to the parking lot and didn't really notice anything wrong but when I went to start it again I got nothing but spinning and puffing sounds from the airbox if I tried with the throttle open...

Hi All Looking for opinions on why this happend Got me a 2010 FE450 a few weeks ago Good shape , starts and works great, fast as hell Had a bit of valve noise so decided to check them , this is what i see the valve retainer is cracked and the rocker has some serious damage to it the...

TLDR; thought I was dealing with an honest person and getting a good deal. And now wondering if and how badly I got ripped off. in need of expertise. I bought a 2010 Husaberg FE 450 today. Rode fine. Started fine etc. All was good. Bike recently serviced etc. So while riding some time after...

anyone know How to repair, Thanks

Hi, anyone have experience with battery inside disruption? allways measure 0 V and infinite resistance. What can cause it? Cheap and expensive battery too. 2002 650

Hey Everyone. Found this bike locally for cheap. It had a rough life.Previous owner broke the kickstart gear and one of the screws for the retaining plate. The screw broke off in the hole. Any ideas how I can get this Screw out without splitting the cases? You can see whats left of the screw in...

Hello. FE470e 2002 A pin is broken, the one on the gear for driving the camchain. Should I just make a new one frome a pice of steel plate, is this okey?? or where can i get a new one? Will a DIY pin do the job.? 2nd: Problem two is a crack on the gear, see pics.. Should i replace this...

So the 570 cases went bust and Im looking for new cases or possibly complete motor from 570, 450 or 390 (same bottom end), any ideas welcome!

Dear All, In 2007 I bought a brand new Husaberg FS650E (2007 model) and from then I just loved it. For the first time since then I have a problem with mi bike. The Primary Gear 29-T broke. It is located on the crankshaft. The part number is 80032000029 and in the manual it is shown as figure...

Righto, so finally have the bike together and running again after installing my Kibblewhite dual valve springs (Thanks for all the advice via PMs Bushy!) I thought I had this job done a couple of weeks back only to realise that the bloody kickstart mech had jammed! Sounds like this a common...

Hi! I still can't get my 650 started. After fixing problems after problems i now think the coil is bad and not working as it should. When using the kickstarter i can get a spark but has to turn it over really fast. Using the electric starter i do not get any sign of a spark. Here is a...

Evening all, hope you are well. I am in need of a little info and help. I posted an intro a while back and I am now in the process of restoring a 1991 FE350. I believe I have WP4054 MXMA forks but have attached a photo just in case. These forks haven't been touched for at least 15 years. What...

so i was kickstarting my bike this morning, and right as i gave it a nice big wallop it kicked back hard and now the kick starter is limp and the pawls or ratchet or whatever wont engage! any advice as to my next step? i imagine its going to mean removing the clutch side cover to access the...

Hi guys, i own a 06 fe450 and it became hard to start. Had to hold throttle whe. It did start as it would not idle. I brought the bike to my mechanic and he checked it. He said one exhaust valve spring on the right side has broken. Now, is that a common failure? Thanks

My original silencer decided to kill itself. The rear cap was to heavy so the bolts ate out the aluminium and it fell off. Anyone got that problem before?

I just had to take a last ride... I knew my chain was worn but not worn enough to snap while doing 80km/h. Outside of the bike seems remarkably little hurt by this, som scratches on the clutch slave cylinder and around front sprocket. But I fear it tore itself up inside because the engine...

Hello husaberg riders, Last time i went riding my husaberg was peeing oil all over the place. I found out that a piece of my engine block has snapped off. All this was caused by a bolt from the camchain slide that has got out of the threads and been making this hole in the engine case. Only...

Hi, I had problem with my bike. When I bought it after few rides, when I changed the engine oil I found a piece of gear tooth. It was tooth from primary gear. Wright now after 40mth I found next piece of tooth in oil. This time is from gear from balancer shaft. Why is it happened...