bearing

I am a newbie and have read through every thread I can find on this topic and saw a few YouTube videos. I was so excited to get this bike and before I could even ride it noticed the oil was milky. I have a few questions that have not been answered in the threads I have read and the videos I...

I have a 2000 fe400 and I think it needs the pushrod ball bearing put in based on what I've read here because the slave doesn't reach the push rod. I have one do I just put it in the pushrod hole and then stuf the pushrod behind it and ram it in or what? I'm afraid if do that it's gonna drop...

Got the rear shock out of my -02 FE650, seems like most of it hasn't been serviced for a while, the oil was a brown sludge (is that normal?), the seals were pretty flat and one side of the top shock bushing fell out when I took the shock out. Got the new seals, but having a hard time finding...

I had a Swede write to me two years ago about the balancer bearing. He'd broken one up and got it out. He sent me these photos (see below). have any of you done this? Do you know the Swede? I need to get the dimension of the circlip groove in the bearing. that is all I need? Anyone...

Hi! Been searching to find the correct STEERING STEM BEARING & SEAL KIT for my Husaberg FS 650 2008. i have searched and found ALL BALLS STEERING STEM BEARING & SEAL KIT - part number 22-1032 , but previously I have swapped with a Husqvarna 701 SM, which had part number 22-1026 . I can...

Hi everybody, long time no see, I unpacked the Berg after long time... I remembered from the last ride somewhen in 2019 that the swingarm bearings were worn out. Long Story short - swingarm out, axle out, bearing out, and under a thick clay crust I could find some needles... Sleeve...

Fitted an RF socket. Broken block after bearing failure.

Hey, do any of you know where to find a replacement? Preferably in Australia! Cheers

I was planning to drain the oil and along with the oil drain plug inadvertently removed the plug for the oil pressure regulator valve. Now I have pressure spring and ball (see pic) from the crankcase and no idea how/where to put it back in. Classic case of oil pan full of oil and a few parts...

HELLO! Got my first Husaberg:) I Have a Berg 470 2002 and need to replace the crankshaft bearings. Read a post here that these should do the job?: NTN NJ206 ET2XCS46 Does anybody know if these fit...

Hi all, currently fully rebuilding my 01 650 engine as it was using alot of oil, don't want to do it again anytime soon so it's having the full works, re plated liner, new piston, bushes, bearings, the lot. The whole bike is getting the works to be honest, however I've read a fair bit through...

Hi to all, Could someone share the dimensions of the water pump bearing, I am hoping to order the bearing prior to pulling the bike apart. Thank you Ray

There is plenty of information throughout this site relating to checking & setting crankshaft end float on 01 to 08 engines but i cant find anything on the 98 to 00 engines where a roller bearing has been retrofitted in place of a ball bearing. It is suggested that axial play on the 01 to 08...

Hi, Took the 2 x covers off the lower joint/bearing. Bearing itself looks and feels good (no radial, lateral, or longitudinal play). But I damaged the two covers in the removal. Don't need the whole bearing replaced - just those two cover rings. Looked high and low, and can't find those...

could anyone please let me know part numbers for 2006 550 lower shock bearings?also chasing a new bump stop,where would i find one? the old one is a mess.cheers

Hey guys, Sent my head off to Thumper Racing for a port job. While I am in the head/rocker cover I want to replace the rocker arm bearings, maybe cam bearings and use a Regina timing chain (Regina was recommended by JBS) Anyone have the rocker arm bearing size and the Regina timing...

Hey husabergers, I am replacing my counter balancer bearings, and as i see my bike only has 1 bearing and not the double bearing. I have bought 2 custom made bearings from orangeberg, but i cannot remove my current bearing. I have warmed up my counterbalancer to around 170 degrees celcius...

Official Husaberg Bulletin #HB-07-03 Main Bearing Update For all Husaberg motorcycles

Any direction as to how to change this. Manual says to use special tool? I have done lower helm a few times and have the motion pro tool for this but I can't seem to find any direction for the upper. Thanks in advance

Hi Bergs, can anyone help me ? I am trying to find which type of bearing and gasket is used in the front wheel in my Berg FE 400 2003. Unfortunately, there are no spare parts in Czech e-shops for 2003. Also Berg representative sells parts only up to 2004. I hope that bearing and gasket is...