This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.

Husaberg FS 650 racing frame

G

Galanius

Joined Sep 2022
29 Posts | 1+
1a2b3c4dB
I was looking some photos and as in the attached photo I observed that frame has some differences. Know some one about that?
 
yes why not!

email me.
I need to check which generation coil it supports. But I think its a 2004+
Taffy
 

Attachments

  • SM underside of frame.JPG
    SM underside of frame.JPG
    44.4 KB
Its an 2004 MODEL italian team Rigo Moto frame with Lazarini driver
 

Attachments

  • 1_lazar-02 X FRAME.jpg
    1_lazar-02 X FRAME.jpg
    101.1 KB
  • 1_lazar-03 X FRAME.jpg
    1_lazar-03 X FRAME.jpg
    20.6 KB
Rigo moto
 

Attachments

  • - - - - - - - - - - - - 1_lazar-04 X FRAME.jpg
    - - - - - - - - - - - - 1_lazar-04 X FRAME.jpg
    18.4 KB
  • - - - - - - - - - - - - 1_lazar-05 X FRAME.jpg
    - - - - - - - - - - - - 1_lazar-05 X FRAME.jpg
    63.7 KB
  • - - - - - - - - - - - - 1_lazar-06 X FRAME.jpg
    - - - - - - - - - - - - 1_lazar-06 X FRAME.jpg
    16.4 KB
build around the engine .its something like wrc cars .they look like the normal cars but no connection at any point . and dont forgett they last for two three races only because the made from very light metal . dont handle for long time like stock .better to to some work on engine axles like MARTIN LIND BIKE and make a x brace under the engine .theese points suffer on stock frame .
 

Attachments

  • SUPERMOTO PIREAUS SATURDAY 438.jpg
    SUPERMOTO PIREAUS SATURDAY 438.jpg
    159.6 KB
  • SUPERMOTO PIREAUS SATURDAY 440.jpg
    SUPERMOTO PIREAUS SATURDAY 440.jpg
    257.8 KB
  • SUPERMOTO PIREAUS SATURDAY 461.jpg
    SUPERMOTO PIREAUS SATURDAY 461.jpg
    247.8 KB
  • SUPERMOTO PIREAUS SATURDAY 395.jpg
    SUPERMOTO PIREAUS SATURDAY 395.jpg
    269.5 KB
Racing frames welded by MIG or TIG? They have the same geometry as stock one or build depend the circuit ?
 
MIG or TIG is not important .they will replace the frame after 2-3 races . the most important is to loose weight .Geometry ussualy change from front fork clamps , depends from open or close sircuit .
 

Attachments

  • 2018 STM Catalogo_Page_061.jpg
    2018 STM Catalogo_Page_061.jpg
    145 KB
because as I can see in your uploaded photos of the racing bikes from the ancient race in Athens on 2004 weld work is below minimum
 
Racing clamps and some other goodies already I have for my project bike. But I am thinking to reinforce my frame to race specs.
 

Attachments

  • B05C3C54-A128-45C2-B4F8-951274BFFD27.jpeg
    B05C3C54-A128-45C2-B4F8-951274BFFD27.jpeg
    1.5 MB
ΟΚ make better weldings from that world championship race team and enjoy your ride . Good Luck
 
If I will perform reinforcements on my frame will be with same material and TIG welding! About the logic that every 3 races replaced the frame i agree but for the reason that is a factory frame must be a perfect product.
 

Similar threads

T
Restoration Husaberg 501 / 1991
Replies
5
Views
221
Tobias427
T
Athamilton
Jetting a Mikuni Carburetor on 1998 Husaberg FE501
Replies
6
Views
450
Athamilton
Athamilton
Extram
Husaberg FS 650 2008 camshaft condition
Replies
4
Views
255
Taffy
Taffy
L
Battery Charging on a Husaberg 650
Replies
1
Views
614
Lukejtg300
L
G
Husaberg Fs 650e 2008 VIN Sticker
Replies
7
Views
648
Galanius
G

Register CTA

Register on Husaberg Forum! This sidebar will go away, and you will see fewer ads.

Recent Discussions