valves

Does anyone have information on what type of valves the 09 has. We all know how simple it is to adjust our valves now. It would be nice for many of us amateur mechanics like myself to get in there without much trouble. I know the motor is different, but I would like to know what it's going to...

as discussed recently the 37s from OEM are £62 plus VAT in the UK so thats £73 per inlet. the problem as you know is that they tulip if revved on OEM cam and valve springs. i have had a few machined down that had gone south. suprisingly they can be saved at 36.8mm and with a taper...

Just wondering if anyone has heard of this method. Iv'e done them this way because my dealer advised it. I just did them at 1/6th out because thats alot of what ive hearing about them. It seems to run great and the idle went a little lower as expected. Seems a little less noisy also in the...

Hi, hope someone can please help! I had a bad running problem at 1/4 throttle so stripped and cleaned out the carb and found loads of dirt so fully cleaned out the whole carb blew it through and put it all back together, while I was there I adjusted my valves as I had yet to do it after...

Do the FE650 come with Titinaum or Stainless steel valves? I have looked for a spec but they are not listed.

looking for valves,guides,seals,springs for 98 fc 501.checked kibbelwhite but only for ktm 450.what about lapping in valve-to-seat? What compound should be used?Can any one help?

Help a newbie out, please? My 'Berg is hard to start. Especially when cold. I'm the second owner that I know of, and I don't know if the valves have ever been gone thru or not. So I figure this is as good a time as any to adjust the valve clearance(s) while I already had the bike apart. But...

This caught me by suprise REEDVALVES in a 4 stroke! How do you inspect them?While on husaberg .com I found that part.Been riding kx 500 c1 since'88.Can inspection be done by removing the two screws holding it in? Whats to look for? My owners manual does't say.Has this been in the forum? I used...

i'm a little confused when the subject of titanium valves are mentioned. how come on a yamaha wr the ti valves last hundreds of hours. how come on a honda crf the ti valves don't last anywhere near that. on a mates husky 510 he got around 7500km before the valves need replacing(under...

Whilst my bike is partially stripped-down I plan to check the camchain tension, valve clearances and timing. What order should this be done in? 1) Check camchain tension? 2) Set Valve clearances? 3) Check ignition timing? Does it matter? I don't think my camchain tensioner spring is strong...

I need advice on a 2000 FC501. I bought it used not running. I took it to a local Husaberg dealer and they told me it has 4 bent valves and will cost around $1000 to fix it! Does anybody have any suggestions? I hate to spend that much money on it knowing I won't get it back out and if I do...

Cheers all! Where do you recommend me to buy titanium valves? Kibblewhite seems like the obvious alternative, but I would appreciate any other ideas as the swedish importer is less fun to work with. I´m looking for 40mm intake valves with 6mm stem, if possible. Thanks!

I have an fs 650 c 2005 and it has been starting easy, kick starting because the battery was bad, replaced it with another defective one. Anyway, do i need to check the valves if it continues to start easy even if I have30+ hours. thanks, edwin

Something bizarre when I try to adjust the valves. I have it at TDC, on the compression stroke. I know because I watched the valves go up and down and also there is no slack in the decomp cable. Adjusting the intake valves was easy. Did the 1/3 turn out. But the exhaust valves, for some...

I just finished checking my valve clearances on my '05 Husaberg at 60 hours. Besides the initial break-in adjustment, where the intakes were slightly tight, the valves have not moved at all. This is in contrast to my KTM 520, where I had to Replace both intake valves at 150 hours due to...

just had my berg serviced valves adjusted & after a short ride found oil leak from the head? removed the tank and found loose hose clamp on the breather hose!!, tightened up clamp test run all seems ok now, you just can't trust anybody. would appreciate any advise on procedure for checking &...

just checked the valves on my 4 month old fe550. i have 2 other bikes (plus a mtn bike or 2), so i haven't been riding it too much, but i'm up to 70 hours and change. the intakes appear to have not moved at all since 28 hrs, and the exhausts seem to have loosened up maybe 1/8 turn or a little...

can anyone explain me how to set the valves where can you check the adjustment i know it should be 0.10 mm but where in the heck do you stick the feeler gauge , like on a regular car or bike motor you can just check the distance between the rockers. :oops:

02 FE400 Inlet Valves can i use KTM or some other brand They want $142 per inlet valve from Berg OZ. I think they are 35mm. If someone can help me out with info or parts in OZ that would be good.

Has ayone here had to replace valves in their older (95) engines? Where is the best place to order them?