torque

any body know what the head nuts and the allen bolts that hold the jujg to the cylinder head need torqued down to ?

Guys, i have booked my 09 570 for the torque limiter to get done, as i am having the problems with the hot start issue. When i described the sympthoms, the dealer knew straight away what i was talking about. Now my question is how long out of warranty has Husaberg Au been sorting this out for...

Has anyone had issues with 09 or later Torque Limiter . I have ruled out all other possible causes of my starter stalling and thus not starting my 450. I have removed the limiter and played with it a bit in the vise ,it seems to work but I dont know the limiting value so I cant test it properly...

My FE 650 starter was slipping. It came time to dig into the bike and get it fixed. I went straight for the Torque Limiter, planning to shim it. To my surprise the "disc spring" or "spring washer" had a section broken. Now the disc spring has like a piece of a pie cut out of it. This is...

Cant find any HP and Torque specs for FE390 on google. Anybody have any HP and\or torque specs for the FE390? Regards Fizz

I searched I swear! :D Would anyone happen to have the torque spec for the clutch center nut for the FE390? Thanks for any scoop! Lee

I’ve got 2 torque limiters here one from my 03 650 and one from a box of spares from a blown 04. Now as I’ve been messing around with the sprag spring (shortening it) I mixed up the torque limiters, from what I’ve read on the site there’s no mention of there being different ones but mine differ...

Although USA Dirt Bike gave restrained queries about the 09 Berg, the May issue of Motocross Action bags it!! They did say they took the lights etc off and used it for MX and things may have been different if it was used in the woods. Main complaint was that it was too heavy!

Can it be done on the bike without removing the torque limiter by just taking the side cover off? Or would it be best while the cover is off to go ahead and pull the clutch and tighten the spring on the sprague clutch??? Thanks. Roland

Any advice? Manual says I need something for 10-100 NM. Other bikes are in inch pounds, and foot pounds. So was researching and can buy like 3 decent analog wrenches to cover the different torque values, but it appears a Snap On Techwrench can do everything??? Same price - one wrench. Anyone...

After reading the owners documents I discovered that my bike has an issued with the aforementioned part. I took the bike apart and tested the slippage. With torque wrench set on 4nm, I tested the disk for slippage and it does slip very easy. What do you all recommend for a shim. I do not...

hey guys, just a quick question, what is the torque spec for the valve covers. i get to adjust mine for the first time today :P Thanks!

Im looking for a spoke torque wrench. The Excel only goes up to 6.9 mil. Is that enough? The 7mm wrench fits. Is 6.9 the right one? . The Fasstco tool says 6.8 and then 7.4. Where's our Husaberg spoke torque wrench? Pollo

Hey guys I searched the site first and checked the the repair/mantainence docs and haven't been able to find how many foot lbs/ newton meters you are supposed to torque your rotors to or your sprockets, also the brake master cylinder for my repositioning bracket. Does anyone know these #'s off...

For the first time today i used a torque wrench to tighten up my forks in the clamps. the settings i was given are 15 & 20 nm, this appeared very slack and i could tighten them up more with an allen key quite easily. are these settings correct or could something have worn in the clamps ?

Hi All, Removed the starter toque limiter today and fitted the one I recieved from Dan at Motoexotica and this has solved the slipping starter problem. I tested the toque of the original one I took only 5Nm hence the slipage, I did the same test with the new one and I could get 25 Nm before...

After rebuilding my 550 motor which included a new sprague clutch due to slipping, when the button was first pressed the same problem persisted so the finger now pointed at the torque limiter, this was about 4 months ago price then was about 60 quid so I thought hell to it I'll use the leg, but...

What's the torque for the head bolts on a 04 450? I searched but found nothing.

Went to visit my closest dealer (Promotopieces, Mascouche, QC) today to check the primary gear nut and balancer nut and fix my starting problem. When I met the owner of Promotopices last weekend and tried to start my 2004 650, he immediately suspected the torque limiter. When the motor was...

Well after a couple of parts sagas, and waiting for spring to arrive, I am almost ready for the inaugural putt-putt on my first berg. Have been assembling tools required for servicing and I recall someone here recommending a beam style torque wrench for doing the valves but I can't recall if...