torque

Does anyone have this torque spec? I can't seem to find it. Thx.

I’ve taken apart my torque limiter but don’t know where to put the shim, and how thick I should have the shim Any info please as I can’t get me my head round the posts I have read about it The cork like material washer inside looks like it will fall to bits if I try taking it out.

Hey everyone just wondering if anyone knows the torque specs for the case halfs on a fe 450 ?? I just purchased a 04 husaberg 450fe and notice the bolts were quiet loose. Are these bikes known for nuts and bolts coming loose?? Anything alts I should check to make sure it’s torqued to specs...

Hi Everyone, I have a question about camshafts, i found a post where somebody said that 08 camshaft for fs 650 2002 is better power on high rpms, and with 53 (original) camshaft the bike have a big torque at low rpm but wont enough in high rpm. What is the better for longer runing hours...

Hi guys I have a 2002 fe501 and was wondering if any1 has the torque settings for the clutch basket bolts ? Thx

I wonder if anyone can give me the exact measure from top to top of the torque limiter in the picture below. It's a FE 650 2007 model Thanks a lot

Hi, I rebuild an FE400E 2002, and I have a question about the value for tightening the nut and the smaller gear. I unmounted the clutch without TQ wrench, and before read somes post of this forum. :cry: Can you give me a approximative value, I will do somes adjustement to have the...

Husaberg Wear Limits and Torque Values From a 2001 Husaberg 400/450 Should work for other models

Hello I have recently bought a husaberg te300 2014 model, does anyone know the tightening torque on the head bolts??? Thanks

What are the torque specs for an 08 650 on the clutch main bolt and the pressure plate screws? Thanks

Pretty much since I got my bike, I've been having a hard time starting it. Sometimes it'll turn over for a few seconds and that's enough to get it going, but mostly it just whines at me and does nothing to the engine. I'm fairly certain that it is the torque limiter, as I've watched a couple...

Just wondering what the torque settings for the head of a fs650c 08 is. Don't have a manual, is there anywhere to download a free one? Cheers Andy

Hi all, What is torque spec for rear sprocket screws, can't find it in 2003 manual. If it's M8 10.9 it can go to 33 Nm, right? Thanks

Can anyone give me value for bottom screw? Top one is 10nm? Are there any difference beetween them - in part catalogue they have got same size but one is marked "SL" and they have got different part numbers.

Does anyone know the head torque for a 2010 FE 390 and will the head come off in the chassis ? or do i have to remove it Thanks in Advance Stan

Hi. My 2005 fs 650e has been having problems starting with the e-start when the engine is cold. the stater just spins and when the engine is warm no problems starting. I removed and disasembled the torque limiter gear and I found 2 cup washers instead of one. should I remove one and install a...

im having trouble starting my fs570 and think it maybe the toque limiter. anyone have a step by step procedure for repairing it? thx in advance for any info, rm

Does anyone know what way the tread goes eg left or right on the gear torque wheel to pull it apart and shim it????? and the best way to hold while undoing the bolt. :cheers:

Can someone please tell me the correct torque for the counter shaft sprocket bolt on a 2011 FE570S ? It must be in the manual somewhere .. but I can't find it!?!?!?

Hi everyone. My first valve check was done by the dealer but its time for #2 and I want to do it myself. I have looked through 7 different threads on this site so pretty comfortable with the 1/6 method. What i did not find here or in any of the manuals is the torque setting for the valve cover...