top

I have a 2002 husaberg FS550, full supermoto swap and single purpose as a Supermoto. I just lost all compression while riding friday and am figuring I'm in need of a top end. What are my options? I would like to have more power, maybe a quicker rev? Do I rebuild as a 550, can I go bigger without...

I am in no way endorsing this shop...but I came across some interesting Dyno results and am quite pleased to see a stock 2006 FS650C beat out all the competition. Cheers! http://www.vancouversupermoto.com/page.php?id=79

My 2002 FX470e is leaking a little oil out the top end. With the bike running a little bit of oil is bubleing/seeping out. My question is, do you think I should just re-torque the bolts on top or replace the head gasket???? or can I just leave it be? Any thoughts would be greatly appreciated...

have a 470 with later top end fitted and therefore no oil feed from the case up through the head to the rocker area. looking at the headgasket laying there all falorn like, i decided to snip a 2mm slit from the the pressure oil feed through to the area in the gasket for camchain to run up to...

Come on Fryguy, give the scoop up. The UHE needs to know. I noticed that one of our top off-road racers in Canada finally switched his web site to Blue & Yellow and there are a bunch of pics of him on an 08 FE. I know you will have me shot if I tell so spit it out already!!! :D

bike started to clonk last time out like a brake pad was loose. soon as you touch the brake in the yard or paddock there is a 'clonk!' i took it to be the headrace bearings and sure enough upon raising the front wheel off the ground i could cloknk the front wheel back and forth 2-3mm. i...

Nick Fahringer put the Husaberg inside the top ten in 7th overall position at the Cherokee National Enduro last weekend in Georgia. This was a big improvement over the first round. Nick was 9 points from Russell Bobbitt, the winner of the event. That's still a lot of ground to make up to be...

Short history: I went for a ride with a couple of guys I met and 1 of them turned up on an 03 fe501. It took a bit to get going, once going would need throttle to keep it going, wouldn't e-start (not even turn over) at all and was a real mission to get it kick started. It was basically running...

Alright, the Rekluse kit comes with a Torx bit and that is what I used to screw the 3mm Torx screws at the top. After putting the bike together I realized the stupid kick start recoil spring had come off (I should have checked before putting the clutch back on, I know). So I tried to...

Top ten Finke Desert Race runner Jared Ewin from Dunedoo NSW has signed to ride for ORANGEBERG in 2008 on a 650 Husaberg, Jared led the over 450 class and was positioned in 10th place on the return trip to Alice last year on ORANGEBERG,s personal Huasberg 650 before an unexpected crash cost him...

Hi everyone, in this case i was so unfortunate i bought a very poorly looked after 501, in which case it needs a new cylinder since it has worn trough the nicasil coating. So I'm wondering where its cheapest to buy one or a cheaper complete bog bore kit is available? Chris:)

From supermotojunkie.com http://supermotojunkie.com/showthread.php?t=37507 I wonder what the new go fast Husaberg Factory Bling items might be? ************* Another Top 5 for Robert Loire & Husaberg at AMA SM Rd 3 Confidence was high in the Team Husaberg pits coming into Rd 3 of...

Confidence was high in the Team Husaberg pits coming into Rd 3 of the AMA Supermoto Series in Tooele, UT on June 23. After having troubles finding a good set-up for the rainy Rd 2 in Englishtown, NJ, Robert Loire still managed an 8th place finish to keep a hold on 2nd in the standings coming...

Friend is rebuilding his 2000 FC501, mostly on the top end where it needs attention. He's replaced the cam, cam bearings, and will be replacing the cam chain....and was asking if it was necessary or even worth while to replace the mechanical cam tensioner?? He said while he's in there he...

Fellow Husaberg Brethren!!! We're $15 short of a record shattering $500 month here at the UHE! When other sites are stuggling to get their members to help with the costs of running a public cycle forum, the UHE members have shown just how much they appreciate Json and all he's done for...

I am getting real close to pulling the trigger on an 07 FE450 that will become a 380 instantly. I dont really think I will ever put it back to a 450. Is there any market for selling the 450 top end? All I am trying to do is to recoup some of the costs that the 380 kit will entail...

I was just concidering a bike event that consists of fairly open terrain and requires top end speed, I have an 04 fe550 ,I run a 16-48 gearing which will give me a top end of approx...

After sucessfully getting the coolant into something other than my garage floor ( thanks for the tip -joe usa - "coolant hose from the botttom of the rad instead of the jug) "duh". i have found the source of the massive clicking noise , http://i51.photobucket.com/albums/f380/ ... ker001.jpg...

Hello all, Did today some dyno work on my supermoto and fast monobike setting. With Slick 2kg 16-40 gear ratio in 6th gear topspeed 18Degrees C 1013Mbar at 8000Rpm's: 180km/u at 8500Rpm's: 192km/u Normally the bergs would go on to 9300rpm's ,but so far I never go,my max revs...

so, i've had my shiny new fe550 for almost 6 weeks, and due to the snowy winter and lots of skiing, i only have 30 hrs (close to 600 miles) in that time. i just did the 2nd valve check. one of the exhausts had moved about 1/12 of a screw turn (or else i left tht one adjusted a little tight last...