swingarm

Well, back here after quite a while, still with the 2010 570 and still going strong! The swingarm bearings are up for renewal and I've bought the repair kit. The swingarm itself moves free but the bolt is stuck solid. After some heafty blows with a copper mallet, no joy and I'm wary of causing...

Anyone know where they still sell swingarm protectors for FE 570 2011? Have been searching and can't find any

Hi everybody, long time no see, I unpacked the Berg after long time... I remembered from the last ride somewhen in 2019 that the swingarm bearings were worn out. Long Story short - swingarm out, axle out, bearing out, and under a thick clay crust I could find some needles... Sleeve...

Hey all, My 2008 FE 550's swingarm has a "bearing inspection window" feature ... :eek: Any hope of salvaging this? Could an aluminum welder "fill in" some of this? JB weld? LOL ... Not keen on dropping $800 Robert Bordens on a new swingarm ... thx, cm

I have an FS650, want to set it up as an enduro/offroad bike. I will keep all the supermoto stuff to swap back. I need a FS650 swingarm and shock to finish this off. Also, I do not believe the 450/550 swingarm shock will work on a 650? Thanks

Hey all, Anyone know what alloy the swingarm would be on a 2000 FC600? Thanks!

Hi Guys Would anyone care to speculate why they changed the simple Bush and Needle Roller setup to the new style, with the caps on the end of the bush in 2005? Pro's & cons? I've had a look at my '03 501, '02 470, and '04 650, and I can't say that I've noticed any strange-ness relating to...

Hi guys! I decided to tear down my bike this winter and pretty much check everything to make sure its all kosher! Right now my bike is completely torn apart and everything looks great, but my swing arm chain guide is worn pretty good, and id like to replace it before putting everything back...

Got myself a -04 fe650. :D After a quick test ride I noticed there's just a washer where there should be a nut, the swingarm axle had snapped the end of it clean off. :eek: Can I fit older (-03, -02, -01) swingarm axle to my 04? From the parts manual it seems they differ from the -04..

Havin a bit of trouble with my swinger. Thought it was just worn bearings/bushes, but the more i look at it - the more i think its somet else. The bearings and bushes look fine. The problem i have is when the swingarm pivot bolt nut is tightened to about 60Nm, the swinger tightens up - the...

Does anyone know if the swingarm pivot bolt from a mid 90's berg will fit an 03 fe400e? The pictures look the same but I can't find any specs or part numbers to compare. Also, if anyone knws a good way to remove a stuck bolt, hitting it repeatedly with a hammer hasn't worked so far!

I have a brand new in bubble wrap swingarm for an 08 FE450 that I want to unload. Dealer cost in Canada is $487. $200 and its yours. I will ship anywhere in NA via Can Post ground for free. scott at rossrochersales dot com

I have a brand new swingarm for a 2008 FE450. I am sure it will fit some older bikes as well. If yours is all beat up, this will make your bike look like new. Dealer cost from Husaberg is $480. Will sell this swingarm for $150. scott at rossrochersales dot com

I have a 2000 fc 501 frame and a 2002 fx 470e frame i am building the fc 501 motor.Which frame and swingarm type would be better??

Hey guys, does anyone have a part number for a swingarm bearing kit for a 2010 fe390? ive searched for individual part numbers on ebay etc, all i could find was the all balls bearing kit, are they any good? seem reasonably priced. thanks.

Hi, I have a 2010 FE390 and when I bought it, it had some swingarm protectors fitted. I've just taken them off and there is some dirt staining on the arms. What's the best way to clean these? I've tried soap and water but am looking for something more potent that won't damage the alloy...

I was wondering if I could fit the swingarm and rear shock from an '06 FE550 to my '00 FC501? I may be wrong, but looking at my bike and the 550, I cannot spot differences on the frame other than engine area Any thoughts?

Hi all im struggling to find a swingarm chain slider for my 2002 650 will one for an 2004 on fit? any help be appreciated thanks

Hi Guys, So during a recent enduro race the sprocket bolts decided to back out and I bit it about 50mph across the desert. Rear sprocket toast, bolts took a big chunk of swing arm and broke off tabs for chain guide and rear hub cracked and pulled apart. And to think I tightened these bolts up...

Hey guys i have a buddy who has a crack in his 2010 fe 390 swingarm and he would like me to weld it. I need to know what type of aluminum it is so i can choose the right filler material. Im thinking its possibly a 6061-T4 or a 6061-T6 but im not sure. If anyone can tell me with 100 percent...