screw

Hello, I need some input on how to replace a broken tappet screw. Any help would be greatly appreciated! Is there an easy way or do I have to pull the head?

2010 Fe450 Little help? Can anyone tell me what this is/does? Fig 40 on fiche? its a 10 or 12mm hex head bolt on the rotor side of the axle under the axle nut. When I tighten it seems to ratchet or click? I just finished replacing the brake pads and installed a new rotor and now the brakes seem...

Hey guys! I'd like to ask where can I find this coolant air bleeding screw? I dont find a proper manual for fe470 2004, heard that it must be close to the spart plug but i dont see any screw there. Could somebody please mark it on the pictures I sent below from both engine sides? Thank...

Hi This is the carb in my 1997 FE400 It's a VHSB flat side By the locaition of the mix screw it should be a air screw correct ? Meaning that turning in will enrich it and out will lean it ? Thanks Nuno

Hey I'm new to this forum just wondering if someone could help me out finding a valve tappet screw for my 2000 fe 400. Ive been looking online everywhere and haven't found anything. I was wondering if there is a good substitute for this part or a good place to find them. Thanks

Hi all, What is torque spec for rear sprocket screws, can't find it in 2003 manual. If it's M8 10.9 it can go to 33 Nm, right? Thanks

hey guys i have just bought a fs650e 05 model and the guy i bought it of said he had it jetted and the mixture screw changed. i was messing around with the tuning and noticed the mixture screw just pulls out of the carby. is this normal? and any tips on tuning would be great! Thanks guys

Anyone noticed that their drive chain has rubbed the kickstand spring screw head off? I have a 2010 FX 450 and a friend has a 2010 FE 450 and we both have the problem. I tried to find some information about this but I didn't have any luck.

Hi everyone. I just ordered an enigne blocking screw for my 2010 FE 390 and im not sure where it threads into. I know its when the engine is at TDC its supposed to "lock" the crank from turning but i cant seem to find where to thread it. any pictures of how to install it? Thanks -Matt

I have a problem on my 2007 FS 650. The idle is a bit low. When turning the idle screw nothing happens!! The idle does not change. Any explanation ?? Thanks Ragnar

Hey Guys, I am not sure what feat of physics allowed me to loose the seat screw for my 08 fe450 but it came off on a ride over the fourth. I called a dealer and they want $36 for a screw with a swivel top. That is a no go for me I will just use a wing screw for it instead. I need to know the...

I am looking to buy a R&D easy access mixture screw. Anybody using one? Are they made well or is the needle part cheap? I dont want to mess up my carb with bits of aluminum.

Hi all, Im looking for a brembo reservoir the 3 screw on the top type for my husaberg as ive bought a radial master cylinder. I want the 3 screw type so i can fit the anodised top. i believe the type im looking for was fitted to the supermoto race bikes does anyone know where i can buy one of...

My 2005 FE550e is leaking oil out of a screw hole in the left side cover. It seems to be next to an oil passage on the cover and I was wondering if it needs a crush washer maybe or if it is a bigger problem. the gasket or cover are not leaking they are properly seated, it leaks around the head...

Where is the coolant bleed screw on the '09/10 FE 450? I just refilled the system but I can't find any mention of bleeding the system in the manual. Thanks, Jay

I have had 09 berg 570 for 11 months, looking for info on the positives and negatives of removing the screw in end cap will I have to adjust FI Mapping to suit? Thanks

Hi all, I've a problem with my Husaberg FE400 2003. I can start my Husa easy with the kickstart, but i can't adjust the optimal mixture. With the motorbike started i can totally close and totally open (6-7 turns) the mixture screw, and the motor don't stop and have no sound change. I think it...

For the guys who have totally removed their throttle stop screws on the 09/10 FE models as per the de-restrict PDF file that is floating around. I just done this and by actually totally removing the screw allows the throttle body butterfly to turn past vertical and actually restrict the intake...

Hello, i own a '07 FS 650 E and although im not a great handy man i used to change the oil and filter on my own. Well, that is until i over-screwed one of the two screws holding the oil-filter (the one on the upper left). Did anyone run into this problem and more importantly how do you...

Phew! Only had my Berg 4 weeks and I don't seem to be out of the garage fiddling with it it! If it wasn't for this site i'd be tearing my hair out! I had some problems with the bike holding an intermittent high idle when warm so I thought i'd start from the beginning and make sure everything...