oil

Hello Husaberg Forum The Clutch on my 07 FE450 is getting lazy.. is not fully disengaging.. so i'm going to start of by bleeding the sistem .. with mineral oil.. would you think 10W fork oil could also work?? ( its red and mineral) Thanks guys Vasco Lisbon, Portugal

Howdy All, Looking into older threads, on the forum, this is a inherent problem with 70 deg bergs. But there is no definitive solution posted. So I thought I would tap into any thoughts. Oil leaking from where the shift shaft spline comes out. The shift shaft has a shaft seal ring (ktm...

Hi, Anyone have tried this hardware on a Husaberg Fs650? Looks nice. https://www.twinair.com/off-road-performance-accessories.php Thank you

Ok hi guys, I did an oil change on my burg it's a fe 450 and i pulled the screen out of the banjo bolt at the top of the engine and now can't remember which way it goes in. The screen is only open one end. Cheers in advance. Sent from my SM-G930F using Tapatalk

Hi guys, I would need your help!! How could I remove the oil filter cover? I have removed both bolts marked as (1) in the image below, but what about the number (2), the center hole in the cover?? Please, help.... Best regards.

Just doing so work on a 70° 450. Workshop manual states that the charge oil pump rotor goes in so the dowel is not visible, the opposite to the suction pump. Well unless I am being very stupid (highly likely!) mine will not go in like that and has to go in the same as the suction pump. Am...

This is really great news fellas. I have a way to increase oil capacity of my Husabergs to about 3 liters. Wim Dercs is racing Husaberg side cars in Nederland and he builds from scratch an oil filter housing with attachment to hook up cooler or what I'll be doing external large spin on filter...

I have a 2009 FE570 and I cannot for the life of me figure out how to get a torque wrench or any ratchet for that matter on the drain bolt or filter screen bolt. Any ideas? Is it just me? They must have some low profile wrenches in the EU because that is a tight @ss fit!

Hi everybody, I hava stupid question :eek: : I recently bought a used FE 450 (MY 2012) and I am not quite sure how to check the oil level as I have a round oil glass but In the manual is only the oval one mentioned. :eek: - So how high should the oil level be in the glass? - And do...

I have a 2013 TE300 and need to change the gear box oil, can I ask what people tend to use? Thanks in advance

Does anyone know the correct name or even a part number for the oil seal that sit behind the gear lever as mine leaks when on side stand it a fe 350 2014 Thanks phill Sent from my iPad using Tapatalk

Is there an oil funnel that fits the funky angle of the filler for a hands free experience?

So the engine is splash/bath lubricated. Primary gear, clutch, idler and kick gear on the left side of the engine, in oil bath. Gearbox on the right side also in oil bath and oil can flow freely between right and left side. Cam, rockers, valves gets splash lubed by the oil carried by...

I know this has likely been discussed but most of what I have found in on the older motors. I am getting a decent amount of coolant in my oil. No oil in the coolant and no leaks from the weep hole. Gasket on side cover looks good. It doesnt seem to be pressuring up the cooling system...

This has been puzzling me since my engine strip. The stretched out spring is the one I removed from the JBS 660. Any idea why someone would do this?

Whilst stripping my project engine fc550 2002 I found this is at simple fix of new seal ? Sent from my iPhone using Tapatalk

Hi fellow Berg owners I have been thinking of getting a stainless oil filter for my FE570 Rally. Have someone tried to fit one? Have done alot of searching and have only come up with the solution on buying one to fit a KTM500EXC (XC) as it should fit, or? The Hilfo HF655 fits both the...

just a few questions please . i have a 2014 te300 husaberg 1. what transission oil do i use 2.how oftern do i change it my local bike shop MCAS gave me bel ray 80W transission oil . will this be okay ?:(

Hey fellow husaberg owners, I just got my berg project finished and everything seems to work! I just cannot figure why my berg consumes oil.. Its mostly while i wheelie i have figured. I have blocked my rear vent and the frame, and fitted a one way valve in my breather mod routed to the...

Hi, Having just bought a 2004 FE501, I'm keen to do an oil change for piece of mind, but I'm struggling to find the right part for the oil filter, and what the grade of oil should be/qty. Any hints on models that share the same filter or a part number would be great, along with what you guys...