oil

I have a Husaberg FE 390 2010, my question is, what type of oil you offer into? And also what type of spark plug? (I want some iridium)

what engine oil brands are our options in the USA? Lots of recommendations for motorex, but that is hard to get in the US. 5w-40 in the winter and 10w-50 in the summer, seems to be the recommendation by the community as well as the manual. My bike is a 2008 fe550. I’ve seen others...

Hello, So i picked up a fe570 with 380hours now. I changed the oil and the oil fiter bolts were begining to strip. I knew i was going to get it fixed but i wanted to squeeze one more ride in, i checked if anything was leaking and it was fine, but when i already felt confident that it was ok i...

I have changed my waterpump shaft seal and it doesnt leak out of the weep hole. I feel like my head gasket is okay because it doesnt create pressure in the radiator. Still the oil goes milky

Hi all, I'm Tanel and I am new here. I recently bought FE 550 E 2006 and everything seemed good till I noticed that clutch cover case, where oil is filled, thread is broken, it is snapped inside (half of it seems to be missing). Oil plug still works and seals (maybe small leak). But question is...

Hi everyone, Just got a 2011/12 fe570 and am wanting to change the oil. I went to crack into it but my 1/2 inch sockets and wrench won’t fit over the bolt between the frame. I’m tempted to use a ring spanner but then I won’t be able to torque them to spec when I’m done. What does everyone...

I have a 2002 fe 501 which is getting coolant in the oil. I have replaced water pump seal and o ring for gearbox cover. Suspect it is a head gasket failure?? Is this common??

Loud noise appeared (on the left side?) after oil change and coolant drain (Took water pump cover off to drain). Bike had about 1.4Litres of grey cloudy oil in it and the coolant was also milky. The breather mod a previous owner installed was also gunked up with water and creamy poop that...

A follow-up question to my oil change parts thread. I've learnt while doing my oil change that I've inherited a problem with 1 of the 2 bolts, the interior thread (in the bore) is stripped...therefore the bolt threads in okay and just spins, without holding any. I'm attaching a pic for...

Hi, Recently become an owner of a 2010 FX450 and the previous owner gave me a box of parts. I'm planning on doing an oil change. I have an oil filter, have oil screens, but my question is, do I need anything else (i.e. crush washer, o-rings, etc...)? Reason I ask, is while looking at the...

Hi, I just bought a 2011 FE570 and while doing an oil change I pulled some rubber debris from the oil screen. The only thing I see in the parts diagram that might match the shape is the valve cover gasket. Any thoughts on what this could be from?

What are you guys using? Brand and weight please... I did a search on the forum... I didn't find anything. Thanks

Hello Huseberg forum. Having an issue with my oil drain plug. Threads got stripped, will have to repais using a time insert. How ever does any one know if it is possible to drain the oil via the oil screen plug? And just leave the oil plug resting still, dont wont to upset those fragile...

Hi just wondering if anyone could help me I’ve got a husaberg te 300 2013. With wp closed cartridge forks. I done a hare and hounds and blow a seal. I’m happy to replace the seal and I know the capacity is 607ml but would anyone be able to tell me how much in the bottom and top of the cartridge...

Went for a nice long ride over the weekend. At the beginning, everything was nice and clean. Then I started to notice a mist of oil on the right side of the engine. It was VERY difficult to pinpoint the source of the leak. The entire right side seemed to have a coating of oil from the valve...

Just got this bike and discover there is little of none oil on the air filter under seat ? , is this normal or do I put air filter oil on it ? thanks , :

Hello! Husaberg FE450 2005 seems to have a problem. Engine ran perfectly but pushed oil trough the breather hose from valve cover. I got sure i got right amount of oil so it wasnt about that. Then i did the engine repair (piston, crankshaft, crankbearings and seals and new waterpump)...

Hello! (There is a short/TL;DR version at the bottom of the post) At first I'd like to apologize for yet another post about flakes in the oil. I know there are quite a few of these threads and should this one be considered unnecessary I will remove it. :) To the case at hand: I...

Hello fellow husaberg riders, I own a husaberg fs650(e) 2006 model. Lately i noticed there was a little oil leak from the little hole where the water pump is (see picture). I looked in the manual and replaced the O-ring as subscribed. After mounting again and a test drive, there was still...

I’ve just finished rebuilding my 96 FE350 and went for the first ride today. I noticed oil leaking from the gasket on the bottom end of the cyl. I first torqued the studs to 44nm then realized from another thread on this forum that I should be torquing to 46ftlbs. I’m currently torqued to...