mount

Hi All, Long time lurker, first time poster and yep, I just got myself a Husaberg after riding Orange for many years. So there I am perusing the threads regarding fuel tanks and I see this nice looking sub mount for the Scotts damper. I have looked around and pm'ed the poster but no luck yet...

will a 2005 ktm 525 scotts steering damper mount fit a 2008 fe650 ???

Have i missed something and is there some mod needs doing to the engine mounts on my new steed?

I have a scotts damper and would like to mount it to my 09 husa when i get it. Dont want to raise my bars anymore than 20mm so guessing that an underbar option is out of the question? Anyone know what post and bar clamp i can use to mount my scotts damper, with my bars in the #3 position...

Just noticed a small crack in the front rhs engine mount (ally?) plate. it hasnt gone all the way down the plate but it is at least 1/3 of the way down. is this a common problem ? Could there be an underlying cause of this or is it something i shouldnt worry too much about and just replace it ...

Any recommendations for flush mount signals for my FE550e?? Also wondering if anyone has installed a twin projector beam type headlight / number plate?? Thanx.

I have to admit that the solution mount thing cleans up the cluster of cables, especially on a dual sported bike, BUT... it is not very solid, Mr Cycra! I had a very little washup in the sand, I did not even stall and left right away, except the handguard was point way up. I could not bend it...

I have Cycra handguards on my Berg, but the way I like to have by clutch lever and the cup, the cable touches the guard mount and it's not super duper. Believe it or not but I do fall (seriously I have been falling very little with the Berg compared to the DRZ, just that one fall happened...

Hallo! I was out riding noticing my frontsuspension worked much smoother than before... I was wondering why, 1, could it be that when I fitted the forks I didn´t mounted it so hard as I use to do... the screws at the lower tripleclamp... ? 2, Was it that I mounted the front...

I just got back from my first ride with installed sub-mount damper installed. Rode some technical rocky sections, it really shines there! Also noticed it on some high speed fire road riding, the front end seems much more stable and planted. I was a little skeptical at first, but I am a convert...

Looking to interchange dirt and sm wheels on an 05 fs 650. will the caliper hit the spokes on the 21" dirt wheel. thanks, edwin

Recently going over my 04 FE450 after a wash & I noticed the bottom radiator mount has broken off the frame. The rubber isolator piece on the stub mounted to the frame is not appearing to come off without destroying it. I'm a little stumped on how to attached the short stud back to the frame...

Do any of you guys have a "sub" mount for a Scott's stabilizer or know if one is available? Will one for a KTM work? Thanks in advance.

Looks as I my have that crack that starts in the area of the rear/right mount on the engine at the swing arm. At this time only small of oil film forms over a 5 hr ride. This is not a problem for me, but is there a possible breakage that may happen in the future and if so is this repairable now...

Any body know if Scotts makes a sub (below the bar) mount for the 05 berg? Will a KT****inM fit??

My new 06 FE450e has rear tire swipe black mark all along the inside of the muffler. I think a friend today discovered the problem. We noticed the left side plastic is off the muffler. Those two little insulated rubber mounts on the inside of the plastic should be near or rest on the muffler...

I pick up my new 06 Fe450e tomorrow. My bar riser and handguard choice needs to work together. I want the fastway handguard system which mounts to it's own bar center top mount. This system works right on top a KTM standard bar mount system. I have seen it many times on KTMs. If the KTM...

Which billet mount do you advise for the Endurance computer? I almost lost mine yesterday if it was not for the kid's keen eyes... Thanks a lot for your advice!

all, I am looking for a good vibration dampning rubber mount triple clamps for my berg. I was thinking about the protaper rubber mount system with a new protaper bar but i dont know which one will fit- anyone have suggestions? the reason why i ask is i think i am suffering from a bit of carpel...

Hi guys! I have owned a FC600 -00 for a month now. I really love this bike and it is the most funny bike i ever tested... (Sorry my english, im from Sweden, the home of Husaberg! :D ) Now to my question, My bik is fitted with 6 gear. I want to put lights on it so i can get a numberplate. I...