loose

Hi! Wondered if anyone has tried or completed - building completely new wiring set-up on a Berg ? I have a 2008 650, and I am planning to start with this: M-UNIT Blue ! anyone read about it or tried to use it to build a new simpler electrical system...

So i bought my first enduro bike around 2 months ago an fe390 however i have been plagued with injection problems for around 15 of the past 20 hours that I have owned the bike and ive been slowly working out the issues. The injector has been replaced as a precaution(and to give me a spare) and...

Whilst taking engine apart I found this little spring any ideas It's 2002 fc550 engine Sent from my iPhone using Tapatalk

My fc 501 got a work out today made about a 100 mile loop on the streets an some highway bike ran strong an even out ran some harleys to 100mph but started hearing a sound from the chain an noticed my chain gaurd had broke an gone so the chain was rubbing the swingarm no biggie but while...

Hi, Well i came from the previous bergs with carbs and now i bought the fe390 2011, i love the bike but there is this issue with the gas throttle that is toooo much loose...i mean the old ones got a good feeling tight grip when opening gas but this one cause its FI( no springs on intake...

Howdy folks, My first post here! I'm the 2nd owner of a 2009 FE570 and the bike came with a few extras, including an FMF Q4 can. The bike only saw some light fire-road use and I've been riding some slow & technical twisties so I put some DEI heat tape on the bottom of the tank and wrapped the...

Yeah, can you believe it? my bike has about 12 hours on it and I took it out a few days ago only to tow it back to the truck. luckily, only 3-4 miles of fairly flat terrain. checked EVERYTHING and thought.."no, it can't be loose terminals" read all the posts about not having a kick start has...

I just got back from an 80 mile ride and the swing arm is getting looser every time out. The nut is tight and it looks like its only the right side. Is this going to be a pain in the *** ? Should I deal with this sooner than later ?

Hey, When I was cleaning my bike today I noticed my radiator was hanging loose! Luckily not much damage was done. The top radiator mounts to the frame are still intact. But the front mountings are both hanging loose. The bolts are still in the radiator but not in the rubber ring on the...

I have an 2008 FE 450 that has 15 hours on it and has developed a leak at the countershaft. From reading the forum the cause seams to be the o-ring behind the spacer. My question is how tight a fit should the sprocket be on the countershaft? Mine is real loose to the point of wobbling a bit, is...

Hallo! My magnets at the flywheel are comming loose... What can I do about it? Fix them with glue? I´ve searched on the topic but couldn´t find any answers! Anyone outthere with a clue? :D /Rikard

I have not had my Berg long but I am learning all the time. Anyhow, I took the right hand frame guard off to replace it with a new set and I noticed that the front sprocket has some side to side play in it and is held in place by a circlip on the splined shaft. Is this meant to be like this...

I recently greased up the head set for the second time this year and found great difficulty in readjusting the bearings. i found that even with excessive preload on the adjustment nut there was still detectable play. so i dropped the forks right out the yokes and checked the lower stem bolt and...

I have a chronic 08 countershaft seal leak, changed it twice. My front sprocket wobbles it seems not to be wide enough to hold the o-ring flush inside the spacer.. whats the deal . Is the front sprocket suppose to be a tight fit or what.. Anyone elses 08 loose/ leaky ??? bought the bike...

a friend just traded for 07 450 and it sounded like a thrashing machine. everyone kept saying husaberg sounds like that, but seemed to me to be getting louder from clutch cover side. i had a 03 ktm 525 once sound like that and intermediate shaft nut came loose and sounded just like this husaberg...

the screw in the left-hand end of the crank has been loose on a couple of occasions but luckily the thread halps it to stay in. it has two flat faces for a special spanner and a jet through it is deliberatley small just to slow the oil pressure. There is another in the big end pin where the...

can anyone give me some addvice on this, whilst ridding a knock started in my engine(07 fe450 30 hrs 1300kms)and i could see the clutch cover vibrating.i layed the bike on its side removed the clutch cover and a bolt had came loose and ground into the cover putting metal fragments through...

I've been out on the bike a few times since it's now running fine but the rivets on the end cap have come loose with the exhaust pressure. I've been out to the garage tonight to remove the rivets and the end cap from the aluminium can. I seem to remember a post last year when someone recommended...

The locknut I found the other day was not the one that came loose last year and wrecked the bike. It is actually the new one that I put in replacement. Same exact valve (intake left). I already talked to Berger about this and he thinks the thread on the adjustment screw might have become...

I am currently rebuilding my top. Rocker cover exploded and bought a newer one, had to reuse my rockers. I have bolted the rocker cover and currently letting the sealant cure. The decomp cable seems to be loose and does not seem to ever need to be pulled to let the piston pass TDC @...