leaking

My bike is leaking coolant out of the weep hole and it's also getting to the oil. The problem seems to be the water shaft seal if im correct. I was wondering if i should buy the oem one or if there is a better one from another manufacturer. Ive understood that the oem one isnt the best one...

Recently purchased this blue beauty, I filled it up all the way yesterday, and noticed gas seeping out of the black circle thing under the rear fender. On closer inspection, it seems to be leaking from all the fastener points. Are grommets used throughout the tank at these points? I laid the...

Question for the group: my water pump seal is more than just weaping, it’s leaking about and ounce or more after each ride. Would it be proper to put in a new gasket, or add some gasket sealant to the original gasket and call it good. Thoughts? Sent from my iPhone using Tapatalk

After filling the coolant up i realized that there was a small hole in the waterpump area leaking coolant and i don't know why, is there anyone who knows what this hole is then please tell me. It's a Husaberg Fe400 1998

Hi Folks, So I recently redid all fuel lines on my 08' FE 450 & have no leaks minus the brass fitting that swivels attached to the carb itself. There must be an o ring that needs to be replaced & Im seeing that theres no retainer on the outside. This tells me it'll likely be a c clip or whatnot...

Hey all, I was pressure testing my coolant system and found that my rad cap was not holding pressure. It bled out through the overflow almost immediately as I was adding pressure. I bought a new 1.4 bar cap and it’s doing the same thing. Anything above 5 PSI (.34 Bar) or so and it purges...

Looks like I have a slight oil leak from the countershaft (output shaft). Behind the sprocket there's a spacer, O ring and a seal. Anyone know if the seal be changed with the engine in situ without splitting the cases? The OEM service manual isn't very specific. Cheers!

09 450. I have noticed slight weeping at the right hand case bolt in the picture. The bolt seems to be torqued to spec. Can I use a thread sealer or anything to address this? Can the bolt be removed while in frame? Thanks

I have a 2010 FE 570 and the sight glass is leaking. Any suggestions or how serious a problem this is. Leaks very little but still bugs me

On my previous rides, I noticed that when I laid the bike down, it would leak fuel. I didn't have time to investigate where from exactly, but naturally was suspect of the vent hose. Today, I took the tank off the bike to mount the cooling under-tank blanket. With the tank off the bike and...

I changed the water pump cover seal and now it's losing coolant really quick. It's dribbling out. Went for a ride around the block to warm it up and see what would happened, when I came back it was violently spitting the coolant out of the hole... I didn't touch the seal inside the impeller so...

This is a 2008 Husaberg FE550 with an Akrapovic Exhaust. I need your help. My bike started to show signs of what looked like some oil spraying around the where the exhaust meets the piston header. The oil is everywhere, so it is difficult trying to pin point where it is coming from, but I...

Anyone know where I can get a rebuild kit for my rear master cylinder or part #. Its a Brembo and it says 8444 on it?

I have a Fe450 from 2009. It's leaking when the engine is started the first time. It leaks for about a minute, than it stops. After it stops leaking there's no problem. I can ride the bike without any problems. It does that every time when i take the bike out for a ride. It's leaking at the...

Hello all, finally decided to get registered on the forum here after reading and wandering around here for a while. I just got myself a husaberg fe 450 supermoto from 2005. It's and absolute beast, did my first testride today but after 10 mins of riding i noticed there was coolant leaking out...

I have a 2004 FE 450 that appears to be leaking oil from the gear shift lever, it also weeps a little bit from the kick start. I have a new seal for the kick start just have not got time to change it yet. Is the gear shift seal an easy seal to replace, or do i need to split the case? Thank you.

Hello all, Last week I found myself without any clutch. It seems that the master cylinder was leaking, so a rebuild kit solved that problem. But the problem wasn't over, so I brought the bike over to the dealership. They installed a new slave cylinder and the clutch was working correctly...

I've got a couple leaks on my new-to-me 390. The tank was on the bike when I bought it, so don't how how the install went or prior owner's history. The red plug under the cdi unit under the seat. What's the best thread tape or sealant to use that's gas-proof? And, there's a black plug in...

I changed water and oil seals with new ones but oil still coming from weep hole. Bearing has two sides so may i install it wrong side? One side of bearing has an plastic so which side i have to put oil seal? Thanks.

Hello folks! I just bought my H-berg FS650 2006(or 2007):happy: and after finally fixing a leaky weep hole, it started leaking oil from the back of the left engine case cover (aka clutch cover?) The gasket was even brand new and everything :eek: After inspecting the clutch cover, i found...