jetting

Hi all I've been enjoing my berg for 3 years now and managed to get the stock Dellortho running well, but i came across a FCR for my other bike (XR 600) so after tunning it for the honda I've decided to try it on the berg also and if happy get anothre one for the XR Anyway i'ts a 39 mm MK2 FCR...

Long time no Berg... See, my 650 got put up about 2 years ago due to knackered main bearings. Anyway, I picked up a new spare engine on the Bay just got it out of the box yesterday. So far it seems 100% legit. Numbers match the tag. It’s a 2008 FE550e engine. Valves were adjusted...

fe650e jetting hello recommendations for jetting and settings my 2004 fe650e please and best place to buy. im in uk at sea level maybe a bit above. and valve clearances please, oil dont want much do i ;) FE not FS

Hello berg lovers. I need your experience about carburator jets. After I have installed akrapovic exhaust and DNA air filter on my fs650e I began to feel the bike a bit strange and low throttle response. I have pushed the acceleration pump a bit and looks better. Couple of days ago a guy with...

Hello from Germany :). I have a 2007 fs650e with a complete akrapovic exhaust. But i need a good Setting for this. Can u tell me your experiance? I have a taffmeister jetting kit for my Berg. Maybe u can post your jetting here and help me with this :cool: My...

Hey guys! Looking for the stock jetting specs for my recently acquired FE650E. It came from a higher altitude and is very hard to start and won't idle. It could be the pilot is clogged and just needs a good cleaning--which I intend to do--but I would like to know if I have the correct factory...

Hi I have been working on a performance jetting kit for my bike which is a well set up FE501e 2003. It has my jap rod in it for testing and until now just the 'easystart kit' for ease of starting. recently i changed a lot on the carb and the PJ was forced up into the 50s! and the bike...

Hi! I've just bought a FE450 from 2006 with a full akra exhaust system. But when I rev just about half way over in neutral and almost full when riding I get a pretty big bog. When its in neutral it will stall if I blip the throttle past half way down. I am completely new to all this and I would...

Hi, can anyone tell me what jetts that should be in the carb in a 2002 650? Mine now has a 190 main jet, above it sits a 35 jet and it is a long 45 jet whit O- ring on it. I struggle whit the bike being werry hard to start when cold(kick for 2-5minutes impossible whit choke) and almost...

I plan to ride in So. Colorado in July with a buddy. We will be hitting a few mountain passes. A few years ago I was near Frazier CO and the jetting was way too rich. Does anyone have recommendations? I am currently at about 1000 ft. in TX with the following settings: Carb: FCR 41...

Altitude Jetting Chart Microsoft Excel spreadsheet Mainjet Sizes Suction-Type Fuel Delivery With Fuel Pump Created by: Gokai134 For carbureted Husaberg motorcycles

Hello I currently drive 178, 85 and 40 jettings in my bike, and I have no power restrictions. Fcr 39 carb and an open Remus slip-on. Would my fellow Husaberg enthusiast recommend changes to my jettings on my fs 450 2005? Owners manual say some FC models for example have 182 etc instead.

Hi does anyone know the correct jetting for my 02 FE650E? It has a stock exhaust, thanks!!

Hello Need some advice here So I got a 1997 FE 400 E with the stock VHSB Flatside Carb It starts OK runs Good in upper throlttle pull hard , but with small throttle opening , like just above idle it's rough , hesitades and stumbles , once past this it' rev hard and fast I've cleaned...

Hi husaberg world, need some advise on jetting a 07fe 550. Ride mainly around sea level with temps around 50-60 degrees. Bike has a 48 pilot, 180 main and 85 aj. The bike would start with no choke for awhile, then wouldn't start warm. Would kick start though. Took carb off and found the air fuel...

Selling, gone back to stock jetting i cant get it right to be honest comes with needle mains 165,162,160,168 pilots 40,38,35 accel pump spacer they charge £80 yours for £50 posted uk only

Hi there been out on the bike a few times since I got it runs great but seems a wee bit leen top end not much the plug is clean and there is no black smoke from the exhaust ever is this good or should there be a bit ???? If I need to riches it up can I lift the needle or do i need to get jets

Hi guys, can anyone give me some advice as far as the best jetting for Moab? Most of the riding will be at around 4000-6000 ft, with one day of going all the way from 4000 to 10000 (la sal pass, if needed I can rejet for that day, but I would rather not deal with this in the middle of the...

As I have been getting acquainted with my 2005 FS650c, and finally sorted out the water pump seal (7 seals, 3 gaskets, and some busted knuckles later), it was time to ride it. The power I expected was not there and the throttle was either on, or off; there was no in between. I guessed this...

My buddy gave a jd jetting module. Im not sure what model it is exactly. its a relatively simple device that plugs in-between the injector and the plug for the injector. the think is the one he gave me doesn't fit my injectors plug. Im already tearing into my wiring harness to thin it out...