intake

94 FE 350 I need the rubber intake boot. Where the carb connects to the engine. Any help directing me where to look would be greatly appreciated. Thanks in advance.

94 FE 350 I need the rubber intake boot. Where the carb connects to the engine. Any help directing me where to look would be greatly appreciated. Thanks in advance.

Just picked up a 99 400FE. Bike runs and rides pretty decently, so I'm just cleaning some stuff up and getting it back up to snuff. At some point in it's life it received a Mikuni TM40 flat slide carb. It's currently got a small (sub ideal) pod filter on it. I'd like to try to get back to the...

A few days ago after about a 45 minutes trail ride I noticed my left leg was getting VERY hot. Made it to the parking lot and didn't really notice anything wrong but when I went to start it again I got nothing but spinning and puffing sounds from the airbox if I tried with the throttle open...

Hi guys, I am new here, from Portugal and got a Berg Fe450 from 06, and what brings me to here is that i need to replace my intake boot and cant find a new one. It seems the part is out of production. Do you know if there is other intake boot from husqvarna or ktm that works? Thank...

Anyone have the rubber intake manifold or know where I can find one?

Does anyone know where i can find intake valves for a 95 fc501 part number 200 00701 have tried all the big companys and small companys email after email phone call after phone call with no help

Looking to purchase cam and intake valves for 95 fc 501 have not been able to locate any please help valve part number is 200 007-01 cam part number is. 200 160-01

Master Wowy asked me to post these pictures of his bike 2000 400fe with a husqvrana intake boot hes very happy with it Husqvarna Intake Boot for 36mm or 38mm Mikuni Carb New | eBay

A while back, someone posted this thesis which I finally had a chance to read. It was very well done by a student who took an FE570 engine and optimized the intake. Page 67 shows the improvement of his tuned intake vs. stock and page 62 shows the effect of varying the lengths of the intake...

wanted intake manifold for 2000 fe400 e..

My 95hr 390 seems to get a build in the throttle body.. Anyone else's do similar?

Hey guys, So I recently purchased a 'berg off a family friend and haven't even been able to go for a ride yet Basically the intake boot was cracked, And when he took it in they didn't use a genuine boot to replace it, Just a standard hose and 2 hose clamps Now, I was just wondering...

Take a look at the PatATi engine: It is a simple two stroke (a piston, a crankshaft and a connecting rod). Without rotary valve and without reed valves it has asymmetric transfer and intake like: For more : http://www.pattakon.com/pattakonPatAT.htm#PatATi Thanks Manolis Pattakos

Anyone use this stuff on their Berg - or any bike for that matter? I've used it on my cars but am a bit hesitant to spray it into the air intake of my FE450.

So the intake roar is quite pleasant on my '09 FE450 for a little while, then it becomes annoying as I am trying to commune with nature while I am blasting white-knuckled through the trees. As an experment, I took a piece of perforated metal to use as a template, laid in on the underside of the...

I have a 2011 FS 570 with only 22 hours and the flash code is blinking one long, 3 short: air intake temp sensor. I have never removed the gas tank. Any ideas? Help? The nearest Husaberg dealer is far far away..... Thanks!!!

It's driving me crazy! After I ride my FE390 I have ringing and roaring in my ears from all the intake noise. I can't hardly even hear the exhaust it's so loud. Any solutions other than earplugs?

Hi all, 2008 450 carbi intake boots keep spitting under the hose clamp on the motor side. Before KTM took over these boots had metal inside the rubber, but no longer. Anyone found a cure for this. I note the 550 and 650 boots are different for the bigger carbi and angle required.

Worried, When I was cleaning the carburator I found a horizontal crack in wall between the two inlet canals. At closer exam it seems to be a ruff mould. But it is still a sort of gap. Do you think it has to be welded or grinded down? Have any body seen the same in your inlet? Please give me an...