install

I just got a sicassracing keyed ignition switch for my 09 fe570. its this one http://sicassracing.com/store/index.php ... cts_id=313 anyway- i cant find anywhere on the harness when a 4 pin plug with go in- something may be hiding , any ideas?

So, I have been slowly gathering parts for my 2009 FE570 to make it trail legal here in Alberta, Canada. Now I am an amateur when it comes to working on bikes and the like, so bear with me. I spent today digging down through the rat's nest of assorted wires, plastic and other things jammed...

Hi: I´ll make the story short. The water pump impeller got screwed (who knows why'). Which was maiking the water boil all the time. I changed the impeller with a new one. Once it was donde, I started the bike and coolant was coming out the water pump through the seal (another problem maybe...

hello i,m a noobie to posting here so bear with me , i,ve just recieved the trailtech stator /reg for 06 fe550 some say it is plug and play , ok i see that the plugs match color code not then i,m leaft with 2 yellow stator outputs that look like they should plug in to a spade with 2 yellow and...

I made a vid of my install of the 70 degree sub tank [youtube:1raskkg9]http://www.youtube.com/watch?v=6BxizgoBYs8[/youtube:1raskkg9]

Hi Iam about to fit one of the Dirt Tricks cam chain tensioners to my 570 and reading the instructions for fitment it says about putting the engine on top dead centre for some models, and to check if this is the case for your bike before fitting, I have used the search function to see what...

So, is it possible to install electric starter to FC model? What would i need(basically)? - Motor - Spacers for mounting - Few gears - battery - Starter switch? Expensive operation??

O.K., I've got what I hope is a stupid question for someone... I got a front axle pull handle with my '10 450, and I cant figure out how to install it on the axle! Am I supposed to drill out the hex end of the axle, and press the pull handle in? HELLLLP! :mrgreen:

Can anyone give me good directions on removing the side case and replacing the clutch. Last time I took the side cover off, I didn't do it correctly and took the kick starter off and then the cover. I was told, after paying to have it put back together, that it throws off the timing of the...

Without sounding like a complete *****, does anyone know where/how to install a "moto led"flasher relay into the stock berg harness on a 2010 FE. The instructions that came with the unit are vague at best and there are only 3 wires so it should not be that difficult but I don't want to short...

Guys, I'm pretty sure I read it here a while ago but a search isn't yielding me anything. Did someone mention a "trick" to installing the fuel tank when you have the radiator fan installed on the right radiator without loosening the radiator and rotating it forward? Man it's tight! Any help...

Hi: I just bought a map switch for my new berg FE450 ´09. How do I install it since it instructions the map came with are no perfectly clear. How do I recognize the cable I have to plug it into?? I tried to fit on the one I though (and it fitted) buy I am not sure if this one is the correct...

Hi. I removed my footpegs from my bike to send them to the painting shop because they look old. Now I can´t install them again I am having problems with the small spring. Is there any trick in mounting the footpegs againg. Thanks for helping. Sebastian

My damper came in, and I installed it today. At first I thought the collar would not work but then I actually read the directions and figured out how to install it - or so I thought. I should have actually followed the directions - what a concept huh? Anyway, the directions say to install the...

Need some help finishing up dual sport lights. I have a new euro wiring harness, factory hi/lo/off switch and a dual filament bulb. Anything easy to check as to why its goes off / lo / off instead of Hi ? Spring's here, need to take off the studs and get road legal. Thanks for any...

Today I installed a trail tech S-8300 stator kit. It comes with a new rectifier and wiring harness. The install was a direct install plug for plug. I had did my homework ahead of time. Trail Tech helped too. I had sent them a photo of my setup. Once I did that they were confident that their...

I just got back from my first ride with installed sub-mount damper installed. Rode some technical rocky sections, it really shines there! Also noticed it on some high speed fire road riding, the front end seems much more stable and planted. I was a little skeptical at first, but I am a convert...

I thought I'd post some pix for those of us who are a bit scared to do such things. I hope these help. Lineaweaver Kit Instructions: Remove: Air boot / carburetor inlet bell, float bowl and slide lid Main fuel jet Needle Pilot fuel jet (long skinny jet near the main jet) Pilot air...

I was just reading about a product called iCat on www.icatusa.com . The site says that the device is supposed to improve the spark that the engine receives. It's installed between your coil and spark plug. Their site says that it helps improve starting and also improves power a small...

How does one install the Boss rad guard? Mine are the slimmer one. Of the two horizontal mounts which hold the louvers and the tank shrouds at the same time, one is longer by an inch. The diameter is too large for it to go all the way through the top holes of the guard. Am I supposed to drill...