install

Hi, I have to install my Speedometer. But there is not enough space between Speedometer, Brakeline and Lamp. Is there anywhere a Picture from original mounted Parts? Thank you very much. Achim. Speedometer is original with 24km on its counter. ;-)

Correct way to install water pump seal Hi everyone, I recently purchased a husaberg fe400e 2002 model. there's a bit of a water leak coming from the wheep hole. The guy before me had done a lot of work to the bike and had actually put a new water pump seal and in, after reading quite a...

Hi all! I just bought a 2000 fe600e and it runs great for about 20 minutes then backfires and flat out dies. I’ll let it sit a few minutes and it starts right back up and runs a couple minutes then dies again. Ive gone through the Dellorto carb fully. Checked float height. New spark plug...

Hey all. I just finished up a valve adjustment, my first one on my new FE570. It went according to all the tutorials and the book and was pretty simple. The only thing I'm worried about is I haven't seen any specific info on installing the cam chain tensioner and I don't want to mess that up...

Sorry for beating the dead horse, this is my first post and a long one(sorry in advance). I just bought this bike last week went for 2 small rides and I was amazed how snappy and responsive the bike is, already in love with the thing but sadly also already having issues. The previous owner...

Hello there, I recently bought a new DJH tensioner for my FS570, before fitting it i decided to called my dealer mechanic and he told me to not remove the factory tensioner without the engine being at TDC or the chain could jump causing the cam timing to go out. I questioned him on this and...

Hello, I am wanting to install my FCR 40 (off an 06 CRF250) on to my 91 501. Has anybody done this install? Mainly looking for jetting specs or guesses. Thanks

Is it possible to install a 660 bigbore kit on a 450? Husaberg Fe 450 2009 and install a 660 bigbore kit?

Bought my bike without these installed but the ex-owner obviously gave them too me. http://i.imgur.com/EPVdCmK.jpg http://i.imgur.com/2YI4Yy9.jpg How do I go about installing them? Looks like I need to take off my front wheel, not sure I'd be confident doing that unless its piss easy. Thanks...

I am fitting the KTM/Husaberg fan kit to my 2010 570 today. Everything fits like it should except i cant find where to plug the thing into my wiring! I was led to believe that these kits are a plug and play deal but there doesnt seem to be a mating plug in my harness! The fan kit has a white two...

Hey guys, Today i took out the Rekluse z-start pro out of my 2010 390, to re-install the OEM clutch. I bought the bike second hand with the Rekluse installed, so i haven't had it all apart myself before. So i managed to get it all back together without a workshop manual, started it up, no bad...

Got a kit for my 2012 TE250 today. Installed everything per the directions and it's not working correctly. I have one of the newer kits with the replacement slave cylinder that has an adjustment bolt on it. The problem is, the adjustment bolt never encounters any resistance until it bottoms...

Well the other day I spent the afternoon installing the new core exp rekluse and the new slave cylinder from rekluse. The exp was simple to install, since I needed an oil change anyway I didn't have to tip the bike, it went in just like any other clutch I just read the directions and went along...

Hi guys. New here and have some stuff to contribute. Thanks for helping me with this issue. 2011 FE570 CA street legal anyone installed a front Safari Tank? see my pics below. 1. the "fuel block" that you install on the stock tank interferes with the wiring harnress, and I can't force the...

Forgive me if I've failed to find this in previous posts.... but, Can someone point me to the correct torques for the clutch cover and "pressure plate" bolts? It's a 2010 FE450 by the way. Thanks.

Hello Group, So what am I doing wrong. 1. Ca-Cycleworks pump arrived this week. Fuel nozzel is 1/4 inch not 5/16 inch as others have said. 2. Others have said use Napa H209 submersible 5/16 fuel line with 13-15 mm FI rated fuel clamp. 3. The NAPA 1/4 submersible fuel line is apparently H315 and...

Hello Everyone, Just wanted to let you know about troubles I am having installing a safari front tank on my 2011 FE 570. Drilling the hole in fuel pump case: 1. The temple appears to be wrong. If you drill the hole where the template specifies, the tap ends up blocking the bottom right fuel...

Hi All, On my 2010 FE390, how do I mount a number plate instead of the headlight? I bought a number plate, but it's not even close to mounting. It seems like the computer gets in the way. You also have to remove the black fender brace too, right?

Hi, Have recently purcahsed a Fan kit for my 2012 FE390. I've read the instructions, what i wanted to know is does the Husaberg radiator need to be removed to fit the fan kit, or can it be installed on the bike. If it does need to be removed can someone tell me the best way to remove it and...

Finally got my map switch from 70 degree racing Unfortunately, the online instructions are for a bike that has different wiring than my FE570S and not getting much help from company Anyone out there install one on a 570S and willing to pass along some tips?