husaberg

Hi Guys. Iv just bought myself a non running 2007 Husaberg from a friend who had it for a long time, it's been stood around 5 years and is in need of a bit of TLC. I'm going to start a project thread and make a start this weekend stripping it down and seeing if I can get it running...

I had several Husabergs from 1989 to 1994. Im looking for a Husaberg close to new as possible or restorable so I can prove to my friends the Berg was ahead of its time. Will try my best to make it look new and would only ride it on nice days to demonstrate the Bergs abilities. Im 57 now but...

Hey guys I own a 1996 husaberg FE 600 and I’m missing a starter gear some where between the starter motor and the crank, is there anyone out there with an exploded diagram of the engine so I can see what gear I’m missing Thanx guys

Hi guys, I'm rebuilding a 04 650 FSE and found flakes on the oil drain magnet. So I took the engine apart for a full rebuild and found the gear dogs pretty worn. I suppose the metallic flakes come from there. I don't have much experience with these parts, the gears are expensive so I...

For sale Husaberg FSC 650 5000 EUR or best offer Perfect condition, very low mileage. Husaberg spent last 15 years in italian shop. Bike has been built in Sweden for championship, lots of modifications. Titanium custom italian exhaust Modified frame head angle Location Poland/Wroclaw (I...

Hi Anyone has experience with putting wider swingarm 5,5" wheel and 180 rear tyre? It is possible to do , but the chain will not go very straight as the frame blocks it from going more out to the side. Can the chain be a bit "bent" or would that be catastrophic?. Only thinking this because...

Hi, I have exhaust for Husaberg 650 in perfect condition for sale, fits to 2002-2004 bergs. Price: 350 euro

How is the timing gear to be installed because I do not remember anymore - it can be put on each side, I assumed that by putting on the upper sprocket and pressing it at 80Nm, it presses the one underneath and I gave it a distance from the side of the second sprocket

Hi ! This is my first time asking for help after no Lucky st my own I have restored a Husaberg fs650 2002-2003 mod. Have timmed the engien for second time without any Lucky. Valve been set right, and timmed by taffy recommeds. I get spark, but wont fire UP. I can not se any fuel on...

Does anyone know whether the shaft nut on the clutch side can be bought somewhere or do you need to buy the original?

I am parting out my fe 400. I can't seem to get it to run, I have taken it to shops, but they cant figure it out. I know they can be compatible with ktms or huskys. Is there any way for me to find out what parts are compatible with what bikes? Also If you want any parts, you can respond to this...

Looking for Husaberg Jersy and pants. XXL - XXXl Jersey 40 - 42 pants Thanks

New never used. One pic looks like it's dirty but it's just how the picture turned out. $85 shipped CONUS from zip 35252. PM me for info or Paypal address.

hi I bought myself a 350 fe 1992 and the engine, the gearbox is in a thousand pieces I wonder if there is any book or blast sketch that you can get

I have a 2010 FE390 with the 70degree tank. The green/blue original fuel line ruptured last week so I replaced it with regular fuel line and reinstalled the check valve as I found it. It also had a shut off valve installed that was partially melted from the exhaust heat so I removed it. Prior to...

Hello. As written in the title I have this situation: Rich at idle, lean off idle. Here is my set up: MJ 155 Taper E (perfect from 1/2 to 4/4). Length K clip 2 (perfect at 1/3). Needle diameter R (perfect to 1/4). PAS 1/4 = PAJ 45 the richest measure (lean to 1/8 ). PJ 35 PS 0.5 the...

hello I'm looking for a connecting rod for my husaberg

is it possible too use a keihin 3900a-drl on a husaberg fe650

I have a 2003 fe 450 that doesn't seem to be getting spark. I took it to a ktm dealer/mechanic but they didn't do anything and all the other mechanics I asked were wussies and don't even want to work on it. I have worked on it myself and have narrowed it down to spark, but the new cdi component...

I have a 2010 FE390 with the 70degree tank. The green/blue original fuel line ruptured last week so I replaced it with regular fuel line and reinstalled the check valve as I found it. It also had a shut off valve installed that was partially melted from the exhaust heat so I removed it. Prior to...