hub

Looking for replacement

Looking for rear wheel preferably and 18” but will be ok with a 19” rear wheel or even just the rear hub for 2001 FC550. Cheers.

I have a 2006 FE650e. My bearings destroyed my rear wheel Hub. Does anybody know what other bikes might be running the same stock hub?

Hello I`m reaasembling the engine but now I have a problem. I want to tighten the 27mm nut in the clutch hub to 120Nm. But I can't lock the gears, and the wheel is spinning. In the repair manual from 2004, it says to use clutch holder 800.29.003.000 (can't find it online) and also to...

Looking for the free wheel hub for my 03 Husaberg fe650 The inner part in the one way bearing for the electric starter. FE450 and FE550 have the exact same part. Not possible to buy from dealer since its not being produced any more. SO if you got one.. New or used i'm interested.

Hello, New to this forum. Just purchased a 2001 501 FE that I would like to use as a dual sport. I have been told I need a cush hub to absorb shock and prevent damage to the front sprocket drive shaft. The question is where do I source this part? I would like to fit TCK80 "twinsport" tires...

Righto, so finally have the bike together and running again after installing my Kibblewhite dual valve springs (Thanks for all the advice via PMs Bushy!) I thought I had this job done a couple of weeks back only to realise that the bloody kickstart mech had jammed! Sounds like this a common...

Howdy Folks, I've got a 2011 FS570, and I'd like to move to a 5" rim. Bunches of folks here just buy a whole new wheel, and I'd rather avoid that expenditure to ease approval by the wifey. My theory is that if I buy the 5" Excel rim, (PN ENJ412N or EMK422N are 32 and 36 hole...

Tackled the good old water pump shaft seal yesterday (milky oil:mad:). After reading many threads on here about it to prepare, I thought it had gone pretty well - until I found I'd fallen in to the "kick start trap"! So while removing the clutch (force parts slipper) I noticed 1 thread was...

WTB: Cush drive hub or complete wheel for 2010 FE Looking to set up my 390 a little better for dual sporting. Let me know if you have something that might work.

Hi all, The front wheel bearing housings are worn on my recently purchased FE450 the old bearings literally fell out when the wheel was removed ! New bearings have been fitted but there is still excessive play in the hubs... Im considering buying a new excel talon rim and hub or a...

I'm trying to mate the sprocket carrier to the KTM cush hub on my sm rear wheel; but the dampening blocks are unyielding to the metal dividers that must slide in between them. Obviously, some kind of lube is needed for the job; but, I'm not sure what product to use that won't damage the...

I have just replaced the rear wheel bearings on my 09 FE450 and found that the rear hub spacer appears to be to long and the bearing that doesnt have the circlip cant be pushed all the way in until the outer race bottoms out in the hub. How do I know that I havnt put to much side load in the...

Hi, new to Husabergs and new to the forum. I have a 2010 FE390. The previous owner has installed a rekluse clutch which includes the rekluse basket, and I'm trying to remove it. (I know...I know... but I like the technical side of clutching and riding). Problem is that I'm trying to remove...

I removed lockwasher and nut and the hub does not just come right off like implied in manual. how do I remove clutch hub and basket without breaking anything? any advise would be appreciated Sorry it is a 2006 fe 650

Last time I pushed the fork leg in a little to cover up the black, but that will add to stiction, right? Of course, like this, the wheel isn't centered between the fork legs, so that will apply some sideways force on compression, which will add to stiction.... How do you guys do it?

I've searched high n low.. I need 3 not a set ! st/st.. UK suppliers ?? Surely someone stocks em ??

Hi all Todays ride finished sooner, as it can be seen [attachment=0:hidhwqvm]Rear_hub.jpg[/attachment:hidhwqvm] My bike is a 02 400, I'm looking for one used rear hub or complete wheel. If someone has one please post. From what I've read here at UHE, the KTM for 01-08 will fit, but the 01-02...

Hello, I have a small problem that my free wheel hub (800.40.025.000) lost couple tooth for the second time during last 40 hours, so I have two questions: 1. How to avoid such failure in the future? 2. Can I remove free wheel gear with all components and use my bike with kick starter till new...

Just realised that one tooth was missing from the big sprocket in the outer clutch hub. Now I need a new one, but the -02 bike seems to be a bit difficult. The original part number is H23014701 but its no longer available, so am I correct that the current part number is 80032000078 (OUTER CLUTCH...