hole

My bike is leaking coolant out of the weep hole and it's also getting to the oil. The problem seems to be the water shaft seal if im correct. I was wondering if i should buy the oem one or if there is a better one from another manufacturer. Ive understood that the oem one isnt the best one...

Hi guys my bike starts leaking by the weep hole behind the water pump, it doesn't stop leaking when engine warm up a little. i read several foruns about the seal, but will be this case? i remove the water pump and didn't notice any failure on the seal (visual) only notice that the seal is in...

Hi, I have just become the proud owner of a 1997 FE400 which I intend to race in the evo class at vinduro events. I'm in the process of getting it set up but I've just noticed a small hole at the back of the water pump housing. It doesn't appear to be threaded so I'm not sure what it's all...

After filling the coolant up i realized that there was a small hole in the waterpump area leaking coolant and i don't know why, is there anyone who knows what this hole is then please tell me. It's a Husaberg Fe400 1998

I was speaking with a new Berger friend about best bang for the buck mods to do on my 08 fe650 and he mentioned- "try the hole in the seat mod to help the engine breath better good for a couple of hp" Has anyone tried this mod, have pics, and jetting specs if it was needed? Thanks!

I have a stripped hole for one of the m6 screws on my clutch cover. It is the one just in front of the oil sight gauge. I can tap it out 1/4 20 but I really don't know how well it will hold. The m6 helicoil uses a 6.2 mm drill bit. Has anyone repaired one of these. Also, it is the hole with...

I changed the water pump cover seal and now it's losing coolant really quick. It's dribbling out. Went for a ride around the block to warm it up and see what would happened, when I came back it was violently spitting the coolant out of the hole... I didn't touch the seal inside the impeller so...

I did an oil res mod on my 570 to increase the capacity. the first time i ran it, no problem just didn't work. I just rebuilt it with larger hoses. in the process, i overfilled the sump by 800cc, which then pushes oil to the res. while running the motor, started to notice a healthy weep hole...

I changed water and oil seals with new ones but oil still coming from weep hole. Bearing has two sides so may i install it wrong side? One side of bearing has an plastic so which side i have to put oil seal? Thanks.

Today I saw that "hole" in my valve cover. Last time it was not there. It looks like it has been eaten by a chain? But the cam chain is tight even without tensioner. Has anyone seen something like that?

Hello, I just reassembled my engine (and used heat shrink to protect the water pump (WP) seal when fitting the side case). When I fired it up, coolant began leaking from the weep hole once the bike reached operating temperature. I figured that it was the WP seal, so I replaced the old one...

So a bit of back story before I get into it I was having major problems with the bike fouling plugs within minutes, so I decide I'd take the plunge and change to the FCR ditching the problematic dellorto, had troubles with the switch but finally had it running and running well with the FCR...

Hi guys, Im rebuilding my bike and im not going to use the starter motor (kick only) im looking for a blank but cant find anyone that sells them? can anyone shed some light on this? looks around 30mm :D look forward to any replys

Hey all you FS 570 owner out there, I decided to cut a hole in my seat over my filter, which I use a DNA filter, after reading it helps make more horsepower, what a difference in power the bike makes it pulls so much harder now, since it can breathe, plus I just put a new muffler on it with no...

Is it possible to just weld this hole? And continue to ride? Or do I have to open it up look for the bits? It works just fine with the hole in there

:eek: 2004, 650 Hus Got oil leaking from weep hole, was just a few bubbles of water but now oil:( From reading earlier threads on this much discussed subject I understand that the water pump seal can be changed by just removing the pump but to repair the oil leak the clutch casing needs to be...

Hey everyone Bought a 2007 FE550 today. It's got the coolant drops coming out which only occur when the bikes warm. It's done 200 hours and probably never replaced. Can anyone tell me what part or part no. it will likely be? I have a hard time finding it in the spare parts booklet...

Hi, I have read heaps of the threads about this but I'm not too sure if I have something different going on or its just the same? I have a 2010 Fe390 3000km on it, never had a problem with the weep hole prior. But..... I just replaced the radiator fluid. drained all the old stuff out and put...

Hi, I have a 2008 Husaberg 650 fe and I had a little leaking problem (oil) out of the little hole near the water pump. I open the water pump and replaced the seal, but everything together but know its leaking water (antifreeze) out of the hole. Any idea what could be the problem?

Hello everyone: My bike is 2011 Husaberg 570 FS.I found this hole cooling water outflow of. Please let me know how to repair Thank you