guide

Hello Husaberg community! My name is Tristan and I am from Washington State, USA. I have a 2003 FE501 that I bought a little over a year ago with ~50 hours on the clock. I put about 10 hours on the bike and it ran decently, but while jetting/tuning the carb I was doing repeated WOT runs and she...

Hello everybody! Owner of Hsb Fe400 1997. I'm looking for a couple of forks guards guide (see picture attached: n° 12 ), in coulor yellow fluoroscent. Many thanks in advance Andrea

Looking for seals for 1996 Hsaberg FE501 Where might these be found?

Hi all New here Where can I find a guide or any thing to look out for on afs650e please? Ta very muchly

Hey folks, I am in the process of repairing a broken timing chain on my 2003 fs650. I thought i was ready to start putting the head back on until my last few parts arrived, the new camchain/timing chain guide (front) is nearly twice the length of the one currently installed on the bike...

Hi, to complete rear wheel refurbishing I renewed sprockets, chain and chain guide as well. Maybe this is helpful for someone... Since the old chain guide is somehow pretty worn I decided to order a new one (pics below). Same with the sprockets. I opted for the original ratio I ordered a...

After my 1st couple of hours riding my "new" 'berg the chain guide plastic insert has started to disintegrate. Anyone have a good/quick source for parts and accessories like this that will deliver to Aus? I want to get some consumables like oil and air filters and anything else you good folk...

The Husaberg Hard Starting Guide by David Lampman has been added to the Service Manuals section. http://husaberg.org/service-manuals/21670-hard-starting-guide.html

Written some time ago by a past member but is still relevant for the earlier models today.

(posted in SM forum as well, but seems pretty quiet over there) purchased a support from motostrano for my 2011 FE570 so i can run a 320 rotor up front for street got the new support mounted all up with the brembo caliper. i tried swapping out the oem guide plate (second shot) to the new...

Hi all, purchased a support from motostrano for my 2011 FE570 so i can run a 320 rotor up front for street got the new support mounted all up with the brembo caliper. i tried swapping out the oem guide plate (second shot) to the new support and it seems to push the pads too far down to get...

Got my engine in to one piece for a long time. :p Still waiting for my yellow as f**k frame and brp special black swingarm. :cool: So I had nothing to do and decided to check everything possible on the engine, valve clearances etc. Timing chain tensioner had only 4 clicks left. :eek...

Hi guys! I decided to tear down my bike this winter and pretty much check everything to make sure its all kosher! Right now my bike is completely torn apart and everything looks great, but my swing arm chain guide is worn pretty good, and id like to replace it before putting everything back...

Well guys, As usual I am looking for parts for my old Berg. I have done surprisingly well. Many shops told me I would not find any parts and others either had the parts or had the generic fix. I am now down to my last bit of items. The hardest one in the 4 valve guide seals for my 1991 fc501...

Hey everyone, I keep damaging the chinsy factory chain guide on my old 97 501e. I have read a lc4 guide will work as a upgrade. Question is will a aftermarket guide for a lc4 also work ?

My factory stabilizer was blown. 1-7 VERY little change. I had a hard time finding the repair kit & procedure. I've posted it here so others can benefit. Kit number is 77012005050. Factory oil is 10W. Fairly easy procedure with no special tools required. [attachment=0:1n3djlt1]Berg...

I broke one of the swingarm attachments (the rear one) to the chain guide. Is it possible to weld on the swingarm or am I relegated to replacing the swingarm?

One of the caliper guide pins on the rear caliper is bent and is wearing the pads at an angle. I unscrewed it to try and straigten it out, but just mangled the threads. I searched bikebandit.com but the schematic doesnt show the pin as a single unit. It shows it as part of the caliper as a...

Is the rubber in the chain guide supposed to split so you can install it without splitting the chain? The old one that I recently wrecked when my crank split seemed to open at the top but the new one I bought (OEM for a 2003 FE) does not seem to open up? Do you have to split the chain to...

The recent destruction of my rear hub also took out my chain guide. I can't find one for my bike at Bike Bandit or Boss Bergs (just '09 +). Where can I get a chain guide for the old girl?