gasket

Question for the group: my water pump seal is more than just weaping, it’s leaking about and ounce or more after each ride. Would it be proper to put in a new gasket, or add some gasket sealant to the original gasket and call it good. Thoughts? Sent from my iPhone using Tapatalk

Does anyone have an address for a gasket manufacturer. Need for the transmission cover. And the head gasket .

Guys, are the copper head gaskets all they are cranked up to be? I have a 610 which is weeping coolant after 2 hrs. Composite with a spray sealer more reliable? Al.

Hi, My first post here, i recently got a hold of a old gal, a FE600 from 93, and it seems that the headgasket did sprung a leak... So i was thinking why not tear the engine down and replace all the gaskets and just a overhaul of it. BUT i cannot find a gasket kit for a 1993, how does the...

Hi all, I am new to the forum and owning a Husaberg. I have a 2006 Husaberg fe550 that is leaking oil below the clutch cover. I was going to buy a new gasket clutch cover and install it but I cannot find where to buy one in the U.S.A. Does anyone know where I can purchase one or have any other...

I bought a 1997 Fe 501 e Husaberg that has brown oil indicating a head gasket leak so I replaced it with a new one and after I got it tightened down and put back together I noticed it was leaking to the outside again. ahh annoying! What should I do? buy a new gasket and try again? The only thing...

Hi again! So after a little ride out today I found out that the head gasket is actually knackered. It started to smoke from around the head which smelt quite sweet so I assume that was the coolant and there's also oil seeping from the seal which was a give away. I am new to this so please...

Hi, by default there is liquid silicone sealing between the cylinder head and the rockerarm cover (Engines 2000-2003). I was wondering if it makes any sense to build a "real" gasket for this part, since I'm afraid that small crumbs of silicone will clog oil channels in the engine somewhere...

I have blown my second head gasket in 60h of riding. The usual place next to the water jacket so compression is leaking out when going WOT. Have been reading about copper gaskets but i cant find someone who still produces them. Anyone knows who stocks them? Or perhaps someone got a CAD...

Hi, So last time I rode my berg I cooked it on really tight single track, and the radiator was only half full after the ride... Now i've discovered that my head gasket is leaking, it's at the front of the engine, I've only noticed it now as the coolant is red and dripped down the sides...

Head Gasket blown on 2006 FE550 yesterday. Rode home fine, no water in oil just spitting out of the front of gasket by the head pipe. I am going to replace this next week, should I be replacing anything else while I am in there. I have 140 hours and 3000 miles on bike. Thanks

I'm trying to find a souce to purchase the gasket inside of the right hand fuel tank petcock on my 2007 Husaberg FE550. The complete petcock is listed as: "50307005000 GAS COCK MIKUNI ON/OFF | 2001". The petcock also fits some KTM's, it is a good, current part number. The petcock is...

I'm re-building my 2005 FE450 and am in need of a complete engine gasket kit. The OEM kit is way too expensive and I need some help from the 'Berg riding community.

The 89-96 models use a base gasket but the 97-00 do not. Does anyone why the gasket was discarded and silicone sealant used in its place?

I keep blowing head gaskets on my 2005 FE650. Does anyone know of a copper or other high quality head gasket that is available in the USA? If not, I will order from JBS.

So about a month ago I went for a ride on my 06 650. I had just replaced the waterpump seal and it was holding fine. After making a quick stop a few miles out to gas up I noticed the overflow bottle had been filled about 6 oz. I thought this was a little strange to heat up that quick and...

Just reassembled my engine. It runs fine now, but the valve rockers don't seem to be getting as much oil as they used to. I didn't check the head gasket when I put the head back on. Is it possible to get it on backwards without knowing? From the outside, the gasket appears to follow the head's...

I never thought i would ask this question, this whole rebuild is really kicking my ass lol... Reusing the camchain, it is the old dark link regina that i believe i read were really good, during dissassembly the tensioner still had plently of clicks left. I marred up one tooth on the camchain...

My head gasket is leaking at the low left corner (when I'm sitting on the bike). Nothing really dramatic for now, but winter's coming and I'll have plenty of time to fix this problem. I've been reading a lot and I can't make up my mind: do I get the stock Husaberg MLS gasket (Part number...

going to be doing complete gasket sets a lot cheaper than OEM even though I use the gaskets. £50/$80 saving on the 2004-2008 sets. I'm launching my web shop in the next couple of weeks so keep an eye out OK? regards Taffy