frame

Hey there! I accidentally purchased an extra frame when I bought my bike recently. I checked through the VIN decoder on the site, and it looks like this might've been a pretty early bike in the 1994 production year? I'd like to know a little more about the bike though to see if it's worth...

Wondering if I will be able to fit as my '02 frame is not compliance plated. alooking for options.

Surplus parts from a FE650 as it's been built into a custom flat tracker (will post later). Pictures attached in pdf so that they're higher quality. 1. Frame with assorted rubbers and battery box. Some surface rust where the paint has scrapped off for instance on the bottom frame rails...

Does anyone have the paint code for the 1999 silver frames?

Has anyone replaced the frame T radiator hose with 90 degree plastic elbow piece attached? I can't get through the frame. I had to cut old hose in half to remove. What is the trick? 2011 FE 390

These seem impossible to find anywhere! Does anyone have the part number for the frame guards? Cheers.

Hi all, I know this is a real long shot, but I'm after a set of good condition frame protectors for a 2010 husaberg 570 or just one for right hand side. Thanks

Wanted to buy 2011 fe450 frame

I had another Husaberg follow me home the other day. Near as I can tell, it's a 2001 400cc FE that was converted to a supermoto. I believe that someone here had it before me as I recall a post somewhere detailing the damage this bike has to the cylinder head. Apparently a cam bolt came loose...

What function do those 2x longitudinal strips of foam on the frame do? The parts fiche says it’s they’re “tabs for filter protection”. Not clear what that means. I took mine off when I sandblasted and powder coated the frame. They were torn and dirty, but I kept them as patterns to...

anyone know How to repair, Thanks

Cheers guys! I'm building a frame for a café racer project. As I would like to copy the rectangular central tube, I was curious about the sheet metal thickness in that box. Do any of you have the possibility to measure it for me? Skickat från min SM-A520F via Tapatalk

A bit of a hybrid question. As part of my total rebuild, I sandblasted and powder coated my frame. I plugged the screw holes, but I overlooked masking off the spots that need to be black remain unpainted for proper grounding. Will need those filed/ground properly - I think the reg/rec...

Hi People Does anyone know what the colour code is for the 2012 frame paint? Thanks Deon

Hi guys My engine is unrepairable and was wondered what engine other than husaberg will fit my frame husaberg fe 400cc 2001. Regards Lucas

Looking for 09-12 70 deg titled frame, or roller for a project I’m putting together. I’m in northern Ohio and willing to travel a reasonable distance to pick up. Otherwise let’s discuss shipping options. Thanks everyone, looking forward to seeing what’s out there.

Hey all, was wondering if it would be viable to swap out a 98 Fe501 engine for a 350 around the same year. Reason being, I lost a water pump seal on a long ride and consequently washed out all my bearings / Engines pretty much done for. However, I do happen to have a 350 (engine only) in near...

Hello, does anyone know where i can get hold of some frame paint for a 2013 TE300, its a the grey colour not yellow, either that or any sort of paint code that i can use to match it, thank you in advance.

hallo, I've just find a sub frame tank for my 390, but, after seen the pics, I'm not sure its connected in the front tank in the right way (there is not a billete fuel pump adaptor plate, but it looks like it should be connected with an auxiliare hole close the original fuel pump. I'm in wrong...

Just got my frame back from powdercoating after some srtrategic strengthening/bracing. Extra cross brace under sump, extra bit of webbing between the 2 frame rails (near exhaust headers), webbing and mount points beefed up at swingarm pivot, extra bracing around headstock.