fc600

Hi people been tinkering around with the dellorto ph38h carb on this monster of a bike and with the spruce up kit that taffmiesters supplied after giving it a clean out and fettling the idle and mixture screws it runs really well . Got some goodies coming from taffmiesters shop who i must...

Hi, I'm new to the site. I've got a '92 model FC600 (since Christmas) and can't find a service manual anywhere. I need to check the timing and valves as the Hussy wont start. It stalled last time out while green laneing and would not start again. I've checked there's a spark, made sure the...

Hello, have seen posts on here regarding the 1/8th and 1/6th method of adjustment . but what is the correct tappit feeler gauge measurement in mm or thou ? . thanks jon

Hello, Just rebuilding my FC600 96 Engine due to the cam decompressor stop coming loose and and falling into bottom end. This took a tooth of the primary drive gear and damaged clutch basket gear, fortuneatly no other damage. I have replaced all engine bearings and piston. crank seems all good...

The bike is being sold as a parts bike. The timing chain broke, the crank, clutch basket, idler and kick start gears are damaged. Engine has very good compression, the bike ran and rode great until the engine failure. I can send photos via email $550.00 Tad Petrie Washington, IL 309-634-1350...

The timing chain broke on my FC6oo. The good news is the engine has great compression with the rocker arms removed so I am assuming the valves are still straight. The bad news is a little piece of the chain made it's way into the straight cut gears in the left side of the engine. I need the...

Almost three years ago the decompression cable broke on my bike, the cable was removed but couldn't find a replacement. I have since moved and the broken cable had been misplaced. I recently found and bought a new cable on line but it is different than I remember the old one being. I recall...

HI. I'm from Poland. Have problem with my Husaberg FC600 2000. I bought it dismantled in box. Had gearbox damaged. I repaired this machine. i try to start this machine and it has not spark on the plug. I check the stator resistance and it is ok. 1. How to check this ICU-10 coil?? It has...

I have a 1994.5 fc600. I need a stator for it. I have the factory parts book, but was wondering if there was a less expensive way to go. I heard a KTM350 stator will also work in it. I want to run lights and street legalize it. The parts book states the stator was the same in all 4 models made...

Any ideas what might have caused this? Do you think the cylinder is bent where whatever exploded the cover hit the outer cylinder wall? Looks a little bent to me... the bike is seriously cheap in price, but a replacement cylinder and valve cover plus whatever broke off in the engine to get...

G'Day All, Have googled myself to death and i cant find a single picture of any of the FC's that Joel would have ridden in the 500cc world championship. Essentially i want to build a faithfull representation of this bike and need some pics to work from. Any help would be appreciated. Thanks...

Hello all, just got my first Berg after many years of lusting after one. The bike came with what I presume is a 1999 501 parts bike (the seller was moving and his wife was making him clean out the garage). I have a yamaha 660 motor sitting around..anybody ever heard of a hybrid Berg?

Hey gang. Finally got rid of my predictabe orange austrian girl and picked up a Swedish Babe. Its the 1999/2000 USA Super TT National Championship winning bike. Rumor has it that its a factory bike. There is a lot of strange welds at the steering head, do they all have that? In any case looking...

Did I buy a '92 FC600 or FE600 ? Can you tell from the photos? I've been told that it appears to be an FE, although the title/vin says FC How can I tell if the 6spd is a wide ratio or close ratio? Thanks DC

Hi would anyone out there have the setup for a keihin fcr 41 for a berg fc600. The bike is starting and ticking over erratically but when throttle is opened, stalls. Any help would be greatly appreciated.

Hi Just to let everyone out there know that I successfully fitted a front end from a 2006 kTM Lc4 660 without any need for modification. The Bearings fitted perfectly and the stem is about 2mm longer than the old bergs so I fitted a shim to take up the slack. All seems to working so far with...

Went out with my cousin and a friend to one of our local riding spots (dis-used old coal mine grounds) at the weekend for a few hours. I was on my '00 FC600 (6 speed), My cousin was on his '03 CRF450 and my friend was on his '04 KXF250. Jumping from one bike to another revealed the following...

Hi everyone, I'm going to tear into the motor to investigate the oil smoke issue (see separate post). Whilst I'm doing this, I plan to replace the camchain, as it's used up almost all of the travel on the tensioner. What upgrades will work on my year 2000 FC600? I see most of the upgrades...

Hi everyone, I've posted a 'WANTED' ad in the classifieds for a gear lever for my 2000 year FC600 and I thought it couldn't hurt to ask here as well! I've been quoted £37 for a brand new lever which sounds extortionate for such a small piece of bent metal!!!! Is it steel- can it be welded...

The clutch on my 1996 FC600 doesn't seem to completely disengage, it makes finding neutral hard and when you put it in gear it tries to kill the engine. I adjusted the cable nearly all the way out; it seemed to help but not completely. Any ideas on what the solution is?