fc550

I just picked up an 02 FC550 with kickstart only yesterday. It had been sitting sine July and would not start, so I drained the gas and put some fresh Premium gas in it. Tried again still nothing, so I pulled the carb off and took it apart and cleaned it out and cleaned the jets. I then put it...

After almost 10 years only 2 failures, counter balance bearing (single row bearing) and just in the last week e-ring on gear/shaft of the oil pump pop off, loss of oil to big end bearing of the crank (low revs at failure). I wished I had purchased more 2001 FC550s, its been a great bike. Thanks...

Hi there my fellow Bergers, Can anyone help me with a replacement rear hub for my '01 FC 550 please? someone must have a destroyed wheel with a good hub out there somewhere? Mate shredded the original one on the weekend at the track, a very messy explosion... :( Cheers in advance for any...

Hi All! I Just finished rebuilding my bike and i added this KOSO water gauge on it. I was just wondering whats the "safe-zone" to ride it in hot summer days? Below 120C ? When should i get worried and turn the bike off.? Thank you!

Ive finally got of my butt muscle and did the final things to complete a rebuild by adding all the vital fluids.My question is after adding the 1 liter of oil and running the engine i noticed the level in the sight glass is not showing oil.The book says it should be visable,i dont have any oil...

As the topic says, can i install FC550 2005 wheels to FE650 2002 without modification? Thänks! -juhis-

Anybody interested, if so let me know. So we can exchange full details. Dont think I'm quite ready for the almighty 550 just yet. Bike is in Excellent condition, with many extras.

Hi! I just bought a Husaberg FC550 2005 bike! I was wondering where could i buy a new exhaust for that bike?? Google didnt help & ebay was empty allso. So im searhing Slip-on or the hole exhaust system for the bike. Help is needed!

Hi! I just bought a Husaberg FC550 2005 bike! I was wondering where could i buy a new exhaust for that bike?? Google didnt help & ebay was empty allso. So im searhing Slip-on or the hole exhaust system for the bike. Help is needed!

hi guys, i need some advice here from africa. i can get a 2002 400 for a very very low price with less than 1000km on. Or for a bit more (ktm 525,kdx 200 used pricerange) i can get a 2005 fc550 with +- 50 hours on very well looked after. i want to use it for a weekend bike and like big...

Hi all! Just got a good offer on FC550 2005 and need some oppinions about the bikes reliability. Is there any major problems occuring on this bike?

I have little knowledge of husabergs and seen a machine in New Zealand (where I'm from) that is described a 2004 550fc with CR gearbox and electric start. here is the link http://www.trademe.co.nz/Browse/Listing ... =266898814 . i am 49yo and have come to the conclusion that I've outgrown my...

This is what i got out off my 2 FC550 '02 Engines. The rocker shafts are totally different, en in 1 of the rockers there is a hole, witch the other one does not have? rockers, 1 from engine #1 (upper) and other one from engine #2 (lower) The other 2 rockers are identical :roll...

Hi, I wasn't satisfied with the way a Keihin carburetor fits to the standard intake manifold and decided to go for an aluminum intake manifold with an original KTM intake boot. The manifold's groove is copied from a KTM cylinder head. This way the Keihin fits perfectly. I'm using the intake...

I just blew up my husaberg fc550. The bike is only ridden as a supermoto, I want some more power, any suggestions while i have the cases split? I would love to upgrade my internals across the board, but i can't seem to find any info on options? PLEASE HELP BERG FAMILY! Also can you swap...

Hello Most fairy tales start with once on a time.... For this forum probably more like I had lying on a shelf.... a Wössner piston part #8602DA with casting mark at the bottom W4108. I compared the pistons, too quickly yes, and installed the Wössner piston. The piston comes 0,3 mm above...

I have bought a kinda cheap FC550 '03 engine lately. The owner mentioned in the advertisement it needed a new Big-end. In this thread I will describe the rebuild of this engine to use it in upcoming SM season. (in my current bike I have an '02 FC550 engine which will be replaced by this one)...

Bought April 2008 new still in the box left over stock.......................Paul

Hey i just rode the 550 with a full ti achro exhaust,the stock jetting was way to lean< the stock head pipes went orange in 2 min.I changed to a 45 pj from a 40pj the clip is still # 4 from top,mj is stock...when the bike is warm and i snap the throttle open it has a bog.....can i shorten the...

Does Husaberg have precut back ground sheets for their bikes ......what im wanting to do is I have a set of numbers that fit a 04-----06 KTM 125sx ---525sx plastic but i was told the rear fender etc is a different shape than KTM Decal works wants me to ship the plastic down to them to cusom make...