drive

Hey guy's, I have found 2 sets of SM wheels ( both sets are for 2003 and up KTM ) one set is a factory 525 SM setup with cush drive hub ( used but mint, comes with everything including 300mm disk and calliper ) other set is aftermarket but no cush drive ( brand new set never installed comes with...

A few of you have mentioned on here that a Rekluse is unsuitable for Supermoto. Why is that? It seems to me that a Rekluse would disengage when you close the throttle, giving you absolutely no engine braking. Isn't that a good thing? A left handlebar mounted rear brake could be modulated to...

Expensive but It looks like this may be the future on dirt riding, they don´t make it for Husaberg but they say they can develop the price is expensive, If I won the lotery for shure I would get this kit "take a look at the videos is just amazing the difference" www.christini.com Hi...

Hey whats the best route for getting a cush drive for my 650C??? Have one built or order a new wheel from the dealer??

What is the advantage of a cush drive rear hub? Is it very noticable? Thanks, Mike

Hi Gang, I've had a good look and can't find the answer, DOC or elsewhere, so can someone help? I note that Dale suggests green loctite for securing the primary drive gear onto the crank end of later model Bergs. My question is, is this just the nut, of are we also loctiting the gear to...

Hi All, New guy here and I have to say that this site is awesome. One of the SMJ members pointed me this way and I'm glad he did. Here is my problem: Primary drive gear broke in half at the key link. Bike is at Longevity Racing (Husaberg dealer) getting repaired. When the primary went...

Hi guys, I'm new to this forum but i've been lurking for a while now, reading as much as i can before i decided to buy a berg. i finally bought a 2004 fs650 motard a couple of weeks ago that had a damaged top end which i'm currently fixing. I noticed my bike doesn't have a cush drive and...

hey everyone.... im kinda new to the whole husaberg seen... so i might need to apologize for my daftness!!! i picked up a very small gem of a husa... (94 frame... rebuilt 96 501) i have decided to somewhat make it into a supermoto... of course i am never going to race it...

As I haven't seen much on this,just the odd reference,I assume it to be not too big a deal but I have to admit it looks scary to me.I went all the way back on this forum as well as the Doc but didn't find much.After one ride the chain has worn into the frame quite a bit such that I have a small...

Folks, check out the pic. Has this happened to you? This was on a 550 FE 68hrs mild riding...

I have a 01 fc 550 that im rebuilding. The counter balancer drive shaft does not roll smooth. it feels like it has notches in it, however the notches are perfectly consistent. It doesn't turn like any other gear or bearing. Is this by any chance normal? Thanks for the help! Rett

anybody has a cush drive for 2000 and up bike let me know cuz i desperatly need one lol

I got hold of a ' 04 FE650 e/6 this week and have a big problem. The starter countershaft gear w/ one-way sprag in it broke most of the teeth off on the clutch hub end (outside). I would think this is highly unusual but not a pretty picture. The case is slightly buggared behind the gear and the...

Anyone knows if it should be a ball bearing or roller bearing on the FE600E -99 on the drive side. I have roller bearing now and my dealer tells me it should be a ball bearing (6203 C3) and there have not been any service upgrade on this, manual shows a ball bearing. Macke

hi all folks, i want to know your experienced thoughts on this one. 95-96' fe 600 transformed from enduro to supermotard. the use is street racing, some trackdays for practice and enduro. the rear hub has no cush drive so there is a straight,hard and rigid power delivery from the engine...

Hi guys, i'm just rebuilding my 03 550 and am unsure about the axial positioning of the balancer drive shaft. it seems to go as far in as you press if until the gear fouls the case, where is it supposed to run? this would surely affect the cam sprocket alignment too. Any help much appreciated as...

Help! I have bought myself a set of KTM wheels for my Hussy as i was told they would fit. What i wasn't told was that the rear is supposed to have a cush drive - which is not available from the seller. Bugger. :cry: Do any of you guys know of a solution - other than paying £100 for a cush...

I have encountered this conversation more than once and want to have an educated answer. I have a buddy who is a big Honda fan. I was talking about Husaberg to him the other day and how impressed I have become with their direction and their bikes in general. One comment he made was "yea, but...