crank

Just wondering here about end float? Just rebuilding a 628cc crank and about to check and adjust if need be the axial play. My other engines have always been around .75-.85mm without any adjustment and run perfectly. A quick measure of this engine ands its just over 1mm. What are the...

I fixed the hot start for my FE450 using the valve adjusments as 0.6 turn . very easy kickstart now, event not necessary to use the decomp when hot. But the Estart not work. Accu is just new , Exide AGM 110 A , i have 2 tried electric startes mitsuba in perfect state . Starter turn...

Hi fellas! I'll be designing some billet cases for my supermono engine this winter. It will be taylormade to my specifications (DOHC-head, big bore, taller conrod, larger mains and a cb in front). In this process, I will also have the possibility to make cases that fit an OEM setup with kick...

Hi, ive got a JBS 700 in my workshop i would like the obtain the 6 pin tool to remove the retainer plates on the main bearings, can the cases be split with those retainers in place or do they need to be removed. Thanks in advance ORANGEBERG

Hello. I have a husaberg fe400 from 2001. The engine has 15h since assembly. But now i have noticed that the crank floats 0.9mm axial. I have ballbearing mains, no rollers. Something dosent feel right.. the bike runs great.. and sounds sweet to. What to do? Is the crank slipping in my...

Hi all, currently fully rebuilding my 01 650 engine as it was using alot of oil, don't want to do it again anytime soon so it's having the full works, re plated liner, new piston, bushes, bearings, the lot. The whole bike is getting the works to be honest, however I've read a fair bit through...

Hi guys, Crank runout on the 570. I get 2.5thou. Does anyone know what the runout is on these? I couldn’t find it in the repair manual. Measured at the end of crank clutch side. Ta.

Fi light flashing now and then... comes on when riding bike will almost quit but clears it self up. When it dose it at start up it won't start but wait 10 seconds and try it again it starts. Checked the harness all looks ok. Would this be a sensor or is the crank moving giving me an air gap to...

the 2001-2003s all used a screw in crank nipple for the oil feed. the 2001-2002s had a tiny 0.6mm hole but that was increased to about 2.5mm in 2003 - the last year. I've had a load of the 2003s made. they will be 7.50gbp plus (if in the EU) our 20% VAT. cheers Taffy

My friend and I were riding today and everything was going fine until we stopped to check a map. We turned the bikes off for a minute and then when we went to leave his bike wouldn't start. It was completely dead, no electronics, no cranking, not even a solenoid click. He tried to bump it...

Looking to shine any light on this issue, any one suffered similar? I imagine the issue could either be caused by bearing failure or crank spread? What's my chances of repairs?

Hi. I have a FC550 2001, 4 speed, with cracked case!:cry: It was quite ok for a while, but now the oil leak is gettig bad. Sooo......I am planning to change to a new (used) crank case, and at the same time, put in 5'th and 6'th gear.... Of course I will totally rebuild the engine with all...

Im looking for a 2005 crank for my 05 berg has anyone got one or knows where i will get one, thanks UK ONLY

I have a crank and rod that came out of my running fe650. The crank and rod seem good. I'm rebuilding with new cases and a lineweaver balanced crank so I have no use for this. Open to offers

Hi Looks like I have a leak from the crankcase on my 650 and might have to split the cases. As I only need to pull the cases apart and re seal the joint hopefully can I just strip the right side take the head off and then pull the cases apart. It looks like all the shafts etc stay in the left...

Hi, After a friend wrecked his 570 engine (http://husaberg.org/lounge/21783-friday-quiz.html#post170404) we are looking for solutions. We got a nice offer from Taffy but sadly my friend is on a tight budget right now. So our solution right now is that I will rebuild his engine using a set of...

I have a 2005 FS650E and need some parts came to local KTM AND THEY CANT LOOK IT UP !! Does any one have any part numbers or anything to help me with this ??

I was wondering if a fe570 cylinder , crankshaft & rod, piston would work on a Fx450 chassis . The cases, head, throttle body has the same part numbers

Heya, I often find myself idly speculating whether a 570 crank (and rod and piston) could be made to fit 550 cases somehow. Probably not! But what are your thoughts on the matter? The 570 stroke is 2mm longer. I should look up rod and piston height too. How much height can you add to...

does anyone here have a 390 crank laying in the workshop? I need the OD of the flywheels please? I'll also buy the crank assembly if anyone wants to sell? thanks Taffy