counter

I'm a new owner of a 2011 FE390 and a new member of the forum, and I want to change my counter sprocket from a 13 to a 14 tooth. Has anyone done that? Is there enough clearance for it? Because it looks pretty tight as far I can see. Thanks for the help.

Hey husabergers, I am replacing my counter balancer bearings, and as i see my bike only has 1 bearing and not the double bearing. I have bought 2 custom made bearings from orangeberg, but i cannot remove my current bearing. I have warmed up my counterbalancer to around 170 degrees celcius...

Hey guys I have this Rev counter and it has a triangular connection that fit with one behind my headlight but it doesn't come on, I tested for power and I'm getting 12v maybe the unit is shot?

Cash drive Vs counter saft failure. The Moxsprocket cush sprocket Earlier This month New Zealand company Motomox released to the public their Moxsprocket. It's a cush sprocket, that has been undergoing hash testing over the last 12months and has performed exceedingly well. The it's a high...

Road riding and Cushdrives V's counter shaft failure Hey guys we know that our bikes are prone to counter shaft wear, and many believe that the issue of the soft counter shaft can be elevated by the addition of a crush drive hub. A new rear wheel is costly (though most of you probably already...

Have a leak from counteract sprocket. Can this be done without pulling case. Love bike so far. Finally got to ride here in northern ca.

I run a 2003 FE501 with a 650 engine fitter. Would it be wise of me to fit a rev counter and if so which type. My speedo is a tech trail 11 which does not have one integrated into it.

I started this topic in the 650 crank balance thread but wanted to post it in its own topic to make it easier to find. The 650 crank thread has a ton of good step by step posts by bushmechanic. I wouldn't have done mine without it. See page 10 for the pictures of my crank...

I need a new pair of balancer bearings. OEM or good quality machine bearings. I consider buying the whole balancer at a good price;) I am not interested bearings from Taffy.

Just fitting a Smiths tachometer to my 04 berg, runs off a 9v battery but I'm not clear from set up instruction how to wire pick up from ignition? Instructions state "connect to contact breaker side of ignition coil"? Blue/White from coil or one of the wires from the trigger? :unsure: Many thanks;)

I split my motor to check things out and the decided to replace piston rings and timing chain, my trouble now is how do i align the counter balancer to the crankshaft, I know what marks to use outside of the case but all of the marks inside of the case are a bit confusing can anyone help

I spilt the cases on my 2001 fc550 to clean up and check out everything after a camshaft bearing let go.Fortunetly, nothing else was affected. Crank bearings and con rod feel perfect after about 150 hrs.Decided to replace balancer bearing while it's apart. My question is the manual says when...

Hello all, Just a tip when updating this part. When I splitted my engine I found the single bearing counter balancer and decided, according the Owner's Doc, to replace it with update part # 210 243-01. This part seems to be discontinued and I received part # 800.30.057.100, balancer model...

hey all, I have some questions regarding the counter balancer (02 470) do they rotate opposite direction of the crank and 90 degrees apart when the piston is at TDC and BDC? can it be long lived with the double bearing set-up or sould one consider removing it for street use?

thanks to ausberg the secret of the rather narrow pair of counter balance bearings is out. i'm having a few sets of them machined down and will let you know what they work out at. i have noted that USA prices are too good for the bearings but i might make some of it back on the machining...

Hi all, i´m owner of a '97 501e. Currenlty i'm rebuilding the engine. With help of this forum i got all non-oem part numbers for the bearings and the sealings...except one!!! The rollerbearing of the counterbalancer sitting in the right crankcase. I destroyed the old one so i cant read...

hey there guys, i am seriously thinking of removing the counter balance on my 2002 fe501 and was wondering wether the spacer can be the bearing that normally sits there or does it have to be made out of steel ?? i am going to be getting the crankshaft balanced after the balancer removal...

Counter balancer slightly out? Vibrates abit at high revs not sure if it is normal or not cause i have changed gearing straight after rebuild? Went from 16/45 to 15/45.

Hello UHE: My FE501e'02 is in maintenance. I'm going tol open the engine to replace piston and cylinder. In same time, I'm going to check counter balancer + ball bearing + circlip + shim ( Manual part 2002 pag. 30 pos. 4 cod. H21024801 ). If you notice, in same manual there is a *4 pos. with...

O.K. this is what I need help with. I have a 2002 470 that blew up a counter balancer bearing and I dont know exactly what was in there. Is this bearing suposed to have a circlip holding it in? Also the manual states that it should have a double bearing balancer, and it does not. Is this a 2001...