clearance

Please help ! How to set the valve clearance FE 390 2011. Instructions would be greatly appreciated, because in my place there are no dealers or authorized repair shop Husaberg. Thank you. :D

well, after 20.9 hours of use the valve clearances on my 450 are in tolerance :wink:

I recently acquired a 99 FE501 thats has a set of supermoto wheels mounted. The chain runs so close to the tire that the chain guard had to be removed, and there is evidence the chain occasionally interferes with the tire. Is there some fix that is missing? Should I simply be looking for a...

2011 BERGS IN STOCK AT RENO KTM! WE JUST PUT ALL PRE 2011 ON CLEARANCE SALE! CALL US FOR PRICES BECAUSE THEY ARE TOO LOW TO PUBLISH! RENO KTM - NMS - NEVADA MOTORCYCLE SPECIALTIES 775-358-4388 * SINCE 1980 540 SOUTH ROCK BLVD. * SPARKS, NV 89431 www.nevadaktm.com 9am-6pm Mon-Sat WE SHIP...

Hey bergers. Just picked up my 2010 FE450. It's my first true off road bike, as opposed to a converted mx bike, and my first serious four stroke. I really like the engine and suspension! On to my question. At 6 hours I checked the valve clearances. Exhaust valves were both 0.14mm, right in...

Greetings chaps, Just recently bought myself a '02 fs 650. The/a previous owner had removed the decompression handle and cable and I'm now putting it back on. On page 22/figure 9D of the '02 users manual it shows a 2mm +- 1mm minimum clearance for the decompression cable, am I correct in...

Hey guys, My front fender rubs my frame and has some scratches on the fender and has rubbed some paint off of my frame. Is this typical? Any good fixes for it?

Does anyone know the valve clearances for fe650 08? and would i need angled feeler gauges? also can't find motorex oil locally can anyone recommend similar i could try? cheers!

Hey, im rebuilding my 04 fe 450 that had a knackered left main (roller). Im going for Enginehardwares method of using a roler on the right and a ball bearing on the left. I want to get the axial clearance right as this is obviously important so went and bought the tool for taking the roller...

Hi guys! today i tried the valve clearance for my 650 berg. removed valve cover and spark plug. put engine in TDC but really can't understand where i have to stick the feeler gauge in. i haven't screwed or unscrewed the nut and the udjusting screw. i looked in the repair manual and tried...

Hi, Can anyone confirm the tappet clearance to use with the LX1 grind camshaft, I have seen .010'' inch ( about .25mm) mentioned, certainly a lot more than std cam clearance? Cheers spanner.

Can someone please give me a step by step approach to adjusting valve clearances on a FE 550 '07'. Heres what I know: clearance is .12mm. Thats it. KTM's have a lock bolt for top dead centre. Bergs? Any help would be greatly appreciated. Yes it is the first time I have done this, but I...

well i've stuck this into two threads and it really is hard just to get a reaction from you lot. not even some of the time, sheeesh, all the time mereckons!!!! ok, most are running - we'll call them - 'grape shape cams by now. the cam flanks are softer and the cam follower bearings seem to...

I did a try to check and set my valve clearance today, but I just can't get my 0,1mm feeler (dont know the exact name for it) in properly? I did not yet remove my radiator but i think that is neccesary to get my feeler in under my rocker arm? Or is there a simple trick for setting the...

Could any one tell me what the axial clearance should be on the main gearbox shaft as I have finished doing a dry assembly but find that it has 0.05mm max (that’s with the right side bearing as far out as possible) , side to side clearance were as the driven shaft (sprocket) has perhaps...

Hello! I am new on this forum, and a newbie with Husaberg. I have bought a 2005 Husaberg FS650E (brandnew, 0 miles/km) I have been riding for more then 500 km now, so i want to check he valve clearance. How do i it? How can i find the TDC?(top dead center) There is no "peekhole" in the...

The axial clearance to the big end, I believe is correct (app. 0,4mm), but the main bearings (rollers) axial clearance is to small (<0,2 mm). I have made sure the mains are properly mounted and all inner races too. 1. Have anyone faced this problem? 2. I was thinking of grinding off the...

Hello, My friend bought my old Berg, and he has bought new original cylinder pipe and Woessner piston. It seems that the clearance is too small, it is only 0.03millimeter, what do You think about this?? Bike 400Fe and the piston is 92mm.. -Mika

I have stripped a 2003 650 motor which has had the roller bearings replaced with balls by DCR. It has a 6206-C3 bearing on the magneto side and a 6206-C4 on the drive side. It is common place to use C3 clearance bearings on a 2-stroke for reasons of lubrication, and I can see why you might want...

G'day, I have purchased a new 550e 04 Berg and ive done about 8 riding hours on it... I spoke to the dealer the other day and he reckons it needs a valve clearance to "protect the heads" or somethign like that... basically giving me the impressing that if the valves arnt adjusted the...