case

02 fe650, just brought it and it started really good with a few kicks. Problem is after letting it sit for a week I went to start it and got nothing before I noticed fuel leaking from all of the exhaust connections at a closer look the crank case is full of fuel. The bike was not running rich...

Hey Guys. I'm a little down right now. I am currently dissasembling my 2005 fs 650e and I noticed that there is a crack about 2" long just above the left side main bearing on the left side case. It's barely noticeable, It doesn't go all the way throught the case. should I worry about it, Am I...

Swapping my FX box for FE gears 1 and 2, parts on the way. Wondering which side case to pull off? From the "cutaway photo", it appears I should pull off the right side, is that correct?

Anybody know where I can pick one up? I am looking for a case saver that bolts to the clutch slave cylinder just in front of the countershaft sprocket.

I have an '05 FE550 and was out trail riding today on some pretty gnarly rocks - the shift lever got bent into the left case and easily scored the magnesium alloy case cover. I'm wondering if anybody makes a case guard for these? (when I got home I ground the sharp edge off of the shifter...)...

http://www.directmotocross.com/news/mx- ... -xtinction

OK, This has been brought up in the past and I thought I could just make this post to give you ideas of what we do. This is the "mod". If you only have a slight amount of oil in your airbox and want to reduce or eliminate it this works pretty good. For higher RPM operation not so much, but good...

I've seen a few queries about the apparently missing fuel after topping off the tank and then after riding a little bit it settles out and is too much to be accounted for by the short time the engine was running alone. So today as I was prepping my bike for a race tomorrow and filling up, I...

Any suggestions for refinishing the stock covers on a 09-10 FE? My bike has 18hrs on it and the covers look like I've taken a belt sander to them.

Well as psot says i have a small Oil leak from Valve case how hard to fix??? do i just remove tank and rad. ?? or is thier more also don't look like it has a seal/gasket can you get them for 501fe 202 or just glue it again ? thanks for your help

just purchased an 04 550 fe, on my first ride l noticed some oil running down the crank case just in front of the water pump housing. there is a small hole in the housing which l presume is for this, but being my first berg i just want to be sure. any help would be appreciated.

Hello, I have an early 2002 FE400e and I just finished splitting the cases for an engine inspection. After searching through many previous posts here, I knew to look for a crack near the swingarm pivot. Well, I found one. At the moment, it is very small hairline crack that is pretty hard to...

Is there a suitable method for splitting the case on a '95 FE without using the Husaberg case splitting tool?

A friend of mine rides a 400 FE. It has been flawless so far but now their are signs of a crack around the swingarm area. I have seen this on the forum before. Anybody have expirience with welding it without opening the engine (as we had planned to do)?

HELLO FELLOW BERG RIDERS I am looking for the left inner case for a 600 fx all years from 97 -2000 with electric start will fit .. The crew a Moto exotica in formed me that these motors are all the same , so any I mean any help would be really GREAT !!!! I bought the bike off ebay and the...

Hi All, I am toying with the idea of destroking my 650 back to a 550 but need to know if this is viable. I need to obtain the rod lengths, piston compression heights and case heights of the new generation vertically split engines in all their variants to ascertain if I can...

Hi, I have 01 berg with a cracked case(close encounter with a rock). Does anyone know the series of aluminum used in the case castings?

Ok, the next thing I'm looking for on my 05 FE650 is a case saver / protector. Anyone know if they are available anywhere?

I have been gathering information on my next bike purchase and one of my gripes with my KTM and others are the excessive oil venting into the airbox from the frame tube crank case breather vent. I was informed that Husaberg resolved this issue in 03, but was not informed of how? Could...

I have a 2000 fc600.I'm changing the water pump seals right know.I noticed that the breather on top of the valve cover just has a hose that plumbs into the air plenum of the frame.This seems odd that this goes back too the intake unfiltered.There is very very little oil from this going in the...