case

Hi all, I'm Tanel and I am new here. I recently bought FE 550 E 2006 and everything seemed good till I noticed that clutch cover case, where oil is filled, thread is broken, it is snapped inside (half of it seems to be missing). Oil plug still works and seals (maybe small leak). But question is...

Hi fellas! I'll be designing some billet cases for my supermono engine this winter. It will be taylormade to my specifications (DOHC-head, big bore, taller conrod, larger mains and a cb in front). In this process, I will also have the possibility to make cases that fit an OEM setup with kick...

Hey everyone just wondering if anyone knows the torque specs for the case halfs on a fe 450 ?? I just purchased a 04 husaberg 450fe and notice the bolts were quiet loose. Are these bikes known for nuts and bolts coming loose?? Anything alts I should check to make sure it’s torqued to specs...

09 450. I have noticed slight weeping at the right hand case bolt in the picture. The bolt seems to be torqued to spec. Can I use a thread sealer or anything to address this? Can the bolt be removed while in frame? Thanks

Hello all! I haven't posted anything since my little new user intro and I thought it was about time to jump in here and share my Husaberg tale. Last year I acquired a basket case 2001 Husaberg FE650E from a friend. I have no prior affinity for Husabergs and no experience with them. I just...

Hi. I have a FC550 2001, 4 speed, with cracked case!:cry: It was quite ok for a while, but now the oil leak is gettig bad. Sooo......I am planning to change to a new (used) crank case, and at the same time, put in 5'th and 6'th gear.... Of course I will totally rebuild the engine with all...

Guys, can anyone point me in the direction of someone that may sell carbon or similar engine covers fro the 570 Berg....can seem to get a line on them anywhere Cheers

Gday everyone. I'm part of a Husaberg group on FB and there's a nice guy that is planning on doing a run of billet case/clutch slave savers. They look real nice, not sure on price but I guess the more he could do, the better it will be. I don't think he's trying to make a profit as such, I...

I pulled my spark plug today (first time since I bought the bike) to have a peek at its condition, and lo and behold the threads were coated in oil. That's not good. I also pulled my breather checkvalve and it had some pooled oil inside, so I'm hoping it's coming from there and not the rings...

Hi Looks like I have a leak from the crankcase on my 650 and might have to split the cases. As I only need to pull the cases apart and re seal the joint hopefully can I just strip the right side take the head off and then pull the cases apart. It looks like all the shafts etc stay in the left...

I was wondering if a fe570 cylinder , crankshaft & rod, piston would work on a Fx450 chassis . The cases, head, throttle body has the same part numbers

I just had to take a last ride... I knew my chain was worn but not worn enough to snap while doing 80km/h. Outside of the bike seems remarkably little hurt by this, som scratches on the clutch slave cylinder and around front sprocket. But I fear it tore itself up inside because the engine...

I know it's a long shot,but I'm looking for a usable right side case half part #220 004-01. Looks like 1989-93 to me. The one I have has been damaged by a tossed chain, and would be very difficult to repair,if it could be done at all. Also, does anyone know if the newer part#220 040-01 is...

Hello husaberg riders, Last time i went riding my husaberg was peeing oil all over the place. I found out that a piece of my engine block has snapped off. All this was caused by a bolt from the camchain slide that has got out of the threads and been making this hole in the engine case. Only...

So my mate done my a favour and sorted a few niggles on my 05 fe 450. Gave it back, problem not solved so I booked into local garage. Mechanic is trying to tell me that the sump plug has been so badly stripped that he can't simply rethread it and that I either need new crank cases or for the...

Hello, Tore into the engine today. Found that the kick starter has started to push into and deform the case along the one edge. This is bad because now the kickstarter assembly doesn't fit properly and is likely causing wear and continual damage to itself (and possible the rest of the engine...

After last ride I noticed that I had cracked engine case. The previous owner already welded that place. And the weld broke. The question is why? And whether it makes sense to weld it again? Can be welded without opening the engine? Engine is 9mth after rebuild.

Just in case someone is looking for one 00' Husaberg 600 Engine Motor Cases | eBay

So I found my oil leak. Appears to be coming from the lower forward area of the case right at the seam. I looked around here but only found the same issue with a 650. Would this be the same as my 450? I also found my engine breather hose has a split in it and lots of oil up in the hose between...

Hi, I make some awesome Case Saver Clutch Cover side guards for the OEM Berg Clutch Covers. These will fit the '09-'12 FE390 thru FE570. These are very light weight but extremely strong. They've been race tested in the Red Bull Romaniacs race and have held up to all kinds of riding. They won't...