cam

i am about to carry out my 1st cam chain replacement. i saw somewhere on this site that someone had trouble on this issue. i would like to tap into the wealth of knowledge on this site, is there anything i need to watch out for. i must get it right the 1st time . i have done cam chains before on...

the husaberg w/salers is closed for the holidays, is anyone aware of a japanese model bike that would suit ??? .

Hi Folks, I need some ideas or advice what to do: As I mentioned in another post, my 1997 FE501E quit all of a sudden while riding in the woods. The diagnosis: the cam gear broke apart and punched a hole in the head towards the water pump. Besides this, there is some metal scraped off from...

Dear gentlebergs: On my 03 FE400e, I had a problem with very rough slow idle and occasional starting problems. My mechanic had been doing a variety of things to try and install an auto clutch per my other posts and thought he would check the timing and rework the jets. When he worked on...

Hey there, I have on 02 400 fe that I have owned for about two weeks. while doing my most recent oil service I discovered bits of a small bearing cage sitting by the oil scree. it turns out it is the cam bearings. I am in the process of tearing down the motor completely for inspection. Are these...

How do the marks line up on the cam sprocket( 1 mark ) crankshaft sprocket ( 2 marks) on a 03' 650 I'm in the process of putting motor back and I can't remember how they were aligned. :x I believe cam sprocket mark is to be @ 6:00 in between the 2 marks on crankshaft spocket @ 12:00 position...

hello, can anybody tell me the difference in numbers,profile of the different OEM cams year 2003-2004 and 2005?? I know that 2004 cam has about 266 degrees. greetings Madero

Hey! Does anyone know what the Duration and lift and timings on in lobe and ex lobe is for the 08 cam stock in 650 -05? Anyone tested to change stock timings anyting? Thx in advance

Just took the 470 for a quick spin, what a difference the 01 cam has made over the 55 that was in it. Its so much nicer to ride not harsh and lairey like it was, oh no. You can actually feel the torque and power of the engine now and although just a quick spin i think i'm gonna like the bike...

Before i open the engine for replacing the cam (thanks to Taffy), i need to know the bearing code of the cam bearings, can somebody tell me that ? Bike is 02 400FE -Mika

hello, I have ordered also a x2 cam for my husaberg 650 2004, My question is do the carb need to reset. I mean much leaner or richer?? the owners or manufact.feel free to respond. greetings Mathieu

Hi to all I have a 2000 400 FE that I replaced rocker rollers and had Linaweaver grind a LRX2 cam, also replaced intake valves and seals for all 4 valves. Well had my first ride on the X2 cam and have some issues. First off I had read that Taffy has an X2 and raved about how quiet his...

I read in Dirt Rider Magazine that Steve Ramones 06 works KTM 450 has a dual cam head run with chain and gears. Talk around my local dealer is that Husaberg will get the same top end. Will it happen in 06? I went in to my dealer to buy an 05 FE 550. Some other lucky fellow just bought the last...

. Hi, this is my first post on UHES and was hoping you guys could help. In 02 I replaced the cases crank cyliner, head piston ect. The rockers appeared to be in good shape...

well i've fitted dale's cam and timed it up this week. i was unlucky in that i had adjusted the original '53' cam i've been running until it was at the end of the slot i had filed in the camwheel. '53' or 'LX2' i would have needed to turn the gear at the bottom of the camchain a tooth around...

I have been running one of Dale Lineaweavers LRX2 cams in my 2000 501 for 18 months now. I initially tried to use my standard jetting but had an over rich condition below 5000 rpm that I could not resolve my self so I asked Dale for some jetting help. If you have a Lineaweaver LRX2 cam in...

question i have just bought a new cam for my fe600 cos the water pump seals were leaking and i was told that the cam had grooves in it so had to change it should i change the cam chain aswell or will it be ok dont know if it's ever been changed 8O 8) :roll: :?:

i've got an 02 470. don't have a bunch of seat time and other than changing oil, thats about it yesterday I noticed some noise that sounded like a cam chain slapping around. are these chain driven and do they require periodic adjustment?

Just for fun! Team Suzuki Flattrack shop cam: http://65.40.185.58:8080/view/index.shtml?videos=one

I have a few questions for all you technically savvy guys out there about engine design and performance. It seems to me that there are a fair number of dual overhead cam designs out there for high performance 4-stroke dirtbikes (maybe more than single cam/rocker arm designs?). I have noticed...