cable

I’m reinstalling the original speedometer on my 2002 FE650, I need to get a new speedometer cable, and trying to figure out how long it should be. I’m not sure how to measure, can’t really figure out exactly how the original cable ran. In front of the fork? Behind the fork? There is no cable...

Anyone know if the 99 speedo cable crosses over to KTMs?

Hi, I have a 2014 TE300. I would like to know what other users are using for an aftermarket clutch lever and cable assembly. Specifically I understand some aftermarket products are available for an easier pull for constant clutching for enduro challenging circumstances. Thanks

What is the function of amal sem cdi White cable? It got 12v when i press the start button. What change this input in the cdi? 2002 bike

Been having some issues on my FE570 09 lately. Symptoms being random slow turnover while actuating the start button, and last ride it cracked up intermittently while riding. Today I went down to the bike pushed the starter button with ecu detached and it was slow turning, grabbed the cable...

After leaving the bike for a month (traveling) the throttle is extremely difficult to twist. Where do I start to clean/loosen it up? FE570

Well guys, I THINK I finally have the ignition and wiring sorted and am about ready to get the old beast going. But... I need a throttle cable (or a set of them?). But, without ordering from GB, does anyone know where I can get one?. The only other remaining question I am battling with is...

1998 FE400 with a Mikuni flat slide carb. What throttle cable do I buy?

loving my Berg, don't get out as much as I should though.. went to the last Watagans Trail Bike rally recently and for the first time noticed the play in the throttle.:confused: Its not much but the more I thought about it whilst riding the more it bothered me :mad::mad: I checked the...

Is there such a thing? Very hard to reach with my set up, must of been done before?:unsure:

Does anyone know where I can get a 96 fe 350 throttle cable?

I bought a FCr carb for my 01 a while back. It is a 39mm that was on a wr450 (according to the seller) the carb only has accommodations for one cable as the entrance hole for the other cable is blank.... It hasn't been drilled and tapped. Has anyone run into this? Is there a problem with running...

i have a 1995 husaberg 501 and i broke the clutch cable and cant seem to find one does anyone know where i can get one or if there is another model cable that will fit. dbrmendomain@yahoo if you know could you drop me a e-mail.

Hey Guys Seeing that it's winter here I thought it would be good time to look a my electronic speedo cable issue on my 2005 fs650e. my issue is that sometimes in the morning (cooler temps) my speedometer reads erraticly. going down the highway crusing at around 110km's it will bounce from...

I have a 1994 husaberg fe 501 enduro Does anyone know what manual decompression leaver and cable would fit and were to get it from as they don't make them to fit this bike anymore Thanks

I'm having some trouble installing new throttle cables on my 2006 650 and could use some advice. Is there any tricks for getting the cables inserted properly into the housing they sit in on the handlebars? Thanks!

Hi, I recently smashed my throttle housing which also damaged the cables. I have since pulled the bike down and installed new cables however I can't seem to adjust them right? I've followed the owners manual, but the throttle just doesn't seem to spring back as fast as it used too? I'd say...

01 fe650. Does anyone have any suggestions on where to re locate the choke cable on my bike. BTW, I'll occasionally have a Clarke tank on it. Thanks

Sense you guys seam to know everything Husaberg here is a question. I snaped my throttle cable today on my 1998 600. My question is I can probably get a new one from motoexotica in California, but does anybody know if KTM cables work or even any Jap Bike throttle cables may work. I have no...

Hej! (That's hi on husa native language) Im trying to reinstall the "dual sport" bits on my newly purcased fe 570 -09 Does enyone know how the turn signal harnesses are supposed to be drawn? The guy I bought it from has unfortunately removed the wiring harnes and the relay as well as the turn...