bolt

Im going to try again this weekend. I have a 2001 FE501 as far as i know it is standard I onlt picked it up earlier this year. I need to get the rear shock off for a rebuild (leaking oil down the 'shaft') A while back I poped the caps off the swing arm, Cracked the nut wound it off a few...

Does anyone know if the swingarm pivot bolt from a mid 90's berg will fit an 03 fe400e? The pictures look the same but I can't find any specs or part numbers to compare. Also, if anyone knws a good way to remove a stuck bolt, hitting it repeatedly with a hammer hasn't worked so far!

Hi there, first post and looking forward to learning a thing or two, hopefully contributing too! Been snooping through some great info, entertaining arguments and the helpful owners doc (which is still index hacked since the other day) for a few months and now purchased an 05 fs650. Always...

Does anybody know what would be the best bolt assortment kit would be to buy for a 1997 FC 501. a little overwhelmed with all the options. Thanks.

Doing my first oil change and i have taken the banjo bolt out and screen out of the oil line othat go into the head. After pulling it apart and cleaning it i noticed that one end of the screen is closed and the other is open.. Now I am not sure which way to install the screen, open end into the...

I'm looking at buying a new 2010 FE 450 (since I can't find a reasonably priced 390) and thought I might try this X bolt bushing for the rear heim joint to drop the suspension a tiny bit so I can put a toe down. Anyone try this? I'm also going to respring to PDS5 rear shock and will keep the 4.4...

Hi, Got a question pertaining to my 2011 FE390 Can anyone tell me if the small mesh strainer in the banjo bolt (p/n 81238016000) on the external oil line to the cyl head is designed to be removed from the banjo bolt for cleaning ?

How much up and down movement should I have in my swingarm with the bike on a stand rear wheel off the ground. Is there a bushing in the swingare that goes bad?

Was draining rad coolant to change it today and at first thought this bolt/plug by kick start lever (see pic) was the air bleed screw...nope...screwed it back in but not sure how far. Found proper bleed screw on R side below the decomp cable and finished up. Any ideas? I went through the fiche...

I'm trying order a special top handlebar clamp for an '09 FE 570, but I haven't recieved my bike yet. Does anyone know the bolt spacing in mm or know if there is an equivalent KTM clamp? Anyone want to measure the 2 spacings on there's? Thanks!

Hi Just pulled out my new husaberg out of the crate. Had to remove the right louver to get to a coolant leak, and found one of the nuts inside the tank is spinning on one of the three 8mm bolts. This is a real hasel as I can see no way of fixing this problem. I can see that with time this...

Hello all I can't get this bolt out of the rear plastic subframe, it just spins the metal collar, any Ideas? Sethro

has anyone got the factory speedo to work with a Magnet in the rotor Bolt vrs the factory magnet. I'm building up second set of rims, after market brake rotor has no hole for the magnet and was wondering if the Trail Tech bolt set up would work. Or has anyone setup a trailtech speedo and...

Hey, As I've decided to keep my '07 FS550E and race it this year (it has under 500kms so far) I've begun to be concerned about this loose crank bolt issue some people have mentioned. Is there a step by step to check this?? I'm pretty green mechanically, can do my own oil changes and...

my 08 650 has its crank locking bolt on the rhs under the stator cover. the 550 motor I have here has its crank locking bolt on the LHS of the crank as shown in the manuals. in the manuals it says to tighten/loosen the flywheel nut with the crank locking bolt to stop the crank spinning...

can anyone give me some addvice on this, whilst ridding a knock started in my engine(07 fe450 30 hrs 1300kms)and i could see the clutch cover vibrating.i layed the bike on its side removed the clutch cover and a bolt had came loose and ground into the cover putting metal fragments through...

Hey guys I searched the site first and checked the the repair/mantainence docs and haven't been able to find how many foot lbs/ newton meters you are supposed to torque your rotors to or your sprockets, also the brake master cylinder for my repositioning bracket. Does anyone know these #'s off...

I notice the crank stop bolt has a plain "thread rolled" end on it. Is it meant to just push up against the crank at any location? On my prevoius bike (KTM RFS), the crank stop bolt was pointed and engaged in a v groove in the crank wheel. On a Husaberg does one just find TDC and then screw the...

What's the torque for the head bolts on a 04 450? I searched but found nothing.

Hi there guys, I have a friend. Let's call him Justin. Justin has an '01 470 FXe. Recently, Justin stripped the head of the allen bolt (lower) on the oil filter cap. Justin purchased new bolts. After running it around a bit and allowing it to warm up, he took his brand new allen...