bolt

Hey Everyone. Found this bike locally for cheap. It had a rough life.Previous owner broke the kickstart gear and one of the screws for the retaining plate. The screw broke off in the hole. Any ideas how I can get this Screw out without splitting the cases? You can see whats left of the screw in...

Would anyone have any idea as to what size the thread is on the rear brake banjo bolt would be? I’m going to try and setup a LHRB and i can get a double banjo bolt but require the size. 2011 FE. Cheers guys.

So After rebuilding my bike i was having issues with the gears. Turns out the old shifter drum bolt which holds the drum to the star piece wasn't tight due to old loctite stopping it pulling in all the way. Saturday i went 38.8miles to FOWLERS of Bristol my local KTM dealer hoping to rebuild...

Hi guys got this allen bolt thats in bottom of engine case/sump on my 2002 650 and its leaking oil. Is it some extra drain plug or something?i have tried searching google and cant seam to find what it is anywhere. Cheers...

I have an 11 Fe390 and can't get the back frame/ tak bolt loose, the threaded rod inside the tank keeps spinning. What can I try???? Help

09 450. I have noticed slight weeping at the right hand case bolt in the picture. The bolt seems to be torqued to spec. Can I use a thread sealer or anything to address this? Can the bolt be removed while in frame? Thanks

Hi guys I been doing some cleaning on my bike and i wanted to replace one of the bolt unfortunately it won't come out, and i actually started wondering WTF is there for? do you guys have any idea? thanks a lot Paolo

Just acquired an 09 450. Changed oil and screens including banjo. How crucial is this to check at each oil change? I assume the bolt correctly aligns with specified torque? Thanks in advance

I have a stripped hole for one of the m6 screws on my clutch cover. It is the one just in front of the oil sight gauge. I can tap it out 1/4 20 but I really don't know how well it will hold. The m6 helicoil uses a 6.2 mm drill bit. Has anyone repaired one of these. Also, it is the hole with...

Hello Im wondering if there are any guides on how to check on the crank bolt? Ive heard that the 2008 Bergs have a problem where the crank bolt will loosen and **** up your bike, and I wanna check on mine. And correct me if im wrong, but there are two bolts, the upper one should be...

Can anyone tell me what this bolt is for? It's leaking oil when the engine gets hot. The bolt seems to have bad threads and I cant get it out.

Does anyone know what is the difference in the swing arm bolt between 2004 and 2005? It is possible that this from 2005 is stiffer?

Attached is a pic of an oil leak that is coming from a bolt that I believe is one of the oil drain plugs. The photo perspective is from the underside of the bike, bash plate removed, from the back looking forward from the right side. These are on the bottom rear of the engine block. To the right...

Gents, I have a 2nd hand 390 of 2011 and the previous owner and me didn't lubricate the axle which goes through the swing arm for about 3 years. For two days I have been lubricating the swingarm axle with very thin oil, heating the engine where it passes through, while at the same time...

I have a 2006 FS650E. From the 2005 workshop manual I can see that there is suposed to be a locking bolt in front of the engine. This bolt does'nt exist on mine...Is there any new location of this bolt or is it just removed?

Gday all, I have been looking for an aftermarket kit like the "Bolt" brand of replacement fastener kits. So far all of the kits have the torx head bolts. Not a major issue, but my 04 have any torx head bolts so I was trying to keep it original. Besides ordering OEM and paying a squillion...

My FS 650 e 2007 , got a problem The retaining bolt[automatic decompression] on the camshaft gear , broke and got between the rocker arm roller [inlet] and the cylinderhead top . result : a hole in the cylinderhead top , broke the roller of the inlet rocker arm . The inlet valves hit the...

Sirs, I have a 2010 FE450 and need to know what direction to loosen the bolt that holds on the sprocket. Thanks! Tim

Several months ago I posted about my 98 FE400e locking up with a THUNK. I haven't had the time to dive into it until this past weekend. Here's what I found: One of the intake valve adjustment bolts broke. I found the end that pushes the valve, but the bolt is just plain gone. I've pulled...

:( Like it says in the Title. I have a 2010 FE450 and, the bolt that connects the front of the composite "subframe" to the upper rear part of the main fuel tank (r/h side) is frozen. I've tried all I can think of to get it to turn but, I'm starting to see the threaded insert in the tank move...