2003

SOLD - 2003 Husaberg FE400 (GTA - Ontario, Canada) Bike sold. Thanks for looking.

Hi could anyone tell me what ohm readings I should be getting please I think stator is poo poo it won’t start and I have a poor intermittent spark I’m getting readings of 145 green to black and 1228 red to black!

Hello all - i just bought a 2003 Husaberg fe400 e. - only 50 hours on it. Brought it my shop to replace the battery, did so and fired right up with electric start. Parked it, and the next day i had no spark. -plug is good - stator makes voltage - cdi box- well its super clean and...

So i've had a look through the forum and im struggling to see what everyone recommends when the stator is bust. thanks for the help!

Good night does anyone know what's going on with my bike I have a new stator could it be the iuc 10? Does anyone know how to repair the module and how to repair it

Hello everyone, I bought a fx650e 2003 built. I need piston , con rod , elektrical stater gear set could you help me?

Hi I bout a beaten up Fe 400 and it has a 19" rear wheel matches the front rim type and appears to be stock ...any ideas other than someone fitted a FC rear wheel to the bike - ps this bike is the roughest berg I own but starts one kick and runs like a little clock. :eek:

Hey, do any of you know where to find a replacement? Preferably in Australia! Cheers

Hi all new to this forum my name is Lee from Cheltenham uk! I’ve recently got myself a 2003? Fe 400 and have a few questions I would like to ask! Q1 I’m a little confused on what year the bike actually is? Engine and frame numbers match with logbook the frame No is YU7FE4E8430000098 which...

Hi guys, I bought a set of ODI half waffle Lock-on-grips and the adapters for the throttle tube don't work with the OEM Domino throttle on my 2003 FE400. There is one adapter that is very close but it's a few mm to large. Not sure what throttle that might have come from. The packaging for...

Im missing the Regulator/rectifier.. Read a post here that a Trail tech regulator/rectifier with 150watt would fit, then i read something about "floating ground" on trail tech that made me confused! anyway, is it possible to use this one: https://www.trailtech.net/7004-rr150 ...

The bike has always been a bit temperamental, today I kicked it over to get it started and found there was no compression. Tried to adjust the valves, both exhaust valves spot on and one intake valve good but the other side adjustment screw will go through the locknut and keep going. Any ideas...

Hi All, Can anyone supply accurate dimensions of the clutch retaining ring, that lock in the half washers on an 03 Fe 501? While doing some clutch work we have lost the original so may make one? Any available out there hopefully in NZ would be even better (part # 23016401) Thanks

Hello I`m reaasembling the engine but now I have a problem. I want to tighten the 27mm nut in the clutch hub to 120Nm. But I can't lock the gears, and the wheel is spinning. In the repair manual from 2004, it says to use clutch holder 800.29.003.000 (can't find it online) and also to...

Hello! I have a Husaberg 650 FS from 2003. Two questions; 1: There is a weep hole near the water pump. It leaks oil from there. What do I need to change? 2. There is also a weep hole underneath the engine block, near the stator. It leaks oil here too. What do I do? Best regards...

Hi, I am having a problem with my bike. Yesterday it fired up on the first kick like it always does, but when i took the chock off it stopped and it will not start again. I changed the sparkplug and still nothing. There is fresh gasolin on it and oilfilter and oil was put on it 2 days...

Hello! Is there any solution to fix Husaberg 650 bad electric starter? The model on the starter is: Mitsuba SM-14 12V I have a spare starter as well: Mitsuba F.N.E 12V (I have never tested it). The starter can crank the engine when i pull the decomp wire, but when I let go, it doesn't...

need a complete engine rebuild kit i.e. bearings and seals ect

Nobody knows if the cam chain tensioner of model 2004 can be fixed on FE 501 2003??? Because the former owner has broken some parts and his mechanic has bought the new parts almost are ok,but the chain tensioner is different and has Ktm code.If I change also the dowl chain tensioner every thing...

Hello can someone give husaberg 650 2003 wiring diagram