week spark please help

Husaberg

Help Support Husaberg:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
A

avi

Joined
Apr 18, 2020
Messages
5
Location
new Zealand
im confused
im trying to get a strong spark from fx470 2001 model
as i dig more to find info about the stator resistance reading more i confused.
some places said between red and black wires i need to have 1.5k ohm and another place its 3k ohm so who is the right?
what i have right now its 1.5k ohm and i think its wrong because the spark is very week.
 
red to black

the 1989-1998 stator wants 1,750 if I recall and the 1999-2003 wants 2,700 plus. between 2,700 and 3,000 is a good figure.

the earlier model green to black is just 23 ohms and the on the later it is 165 ohms.

Taffy
 
On my Husaberg FC550 2001, I had the same problem, very weak spark. My stator was reconditioned, the flywheel mag where in great shape. So was last was to open the CDI/coil. I found the high voltage lead to the spark plug burnt at a copper pin in the CDI/coil. I installed new copper wire high voltage lead and soldered the copper lead to the pin. I have had no more problems with the weak spark. But now my flywheel mag are starting to crack a little. But she still starts and runs well. Maybe Taffy can recondition your CDI/coil.

Mars
Husaberg FC550 2001
KTM SX250 2010
KTM XC-W 250 2019
 
I can certainly do that Mars. But that shouldn't detract from him looking at the right things in the right sequence!

one of the biggest problems with the FC is that people forget to lay the stator on an alloy ring in the stator cover.

regards

Taffy
 

Attachments

  • 470 stator spacer.jpg
    470 stator spacer.jpg
    13 KB
Taffy,
Is the stator aluminum spacer applicable for a 2000 FC 501 as well?
Hakan
 
Taffy said:
I can certainly do that Mars. But that shouldn't detract from him looking at the right things in the right sequence!

one of the biggest problems with the FC is that people forget to lay the stator on an alloy ring in the stator cover.

regards

Taffy
Click to expand...

is this spacer also need for the 470? i dont have it and im using an after market stator
 
I don't know Avi.? I don't know what that stator looks like. the thing to remember about an FC stator is that it is so thin it doesn't get into the middle of the flywheel. It might not be the stators fault though because despite what I just said, the next thing to remember is that the flywheel isn't very tall either!

...it doesn't come out from the crankcases so far! I have a brand new FC flywheel here and used FE flywheels with which I could take a photo.

I attach a photo of a very thin FC stator....

now i've shown you mine you can show me yours! ;);)

regards

Taffy
 

Attachments

  • MX SEM 1.jpg
    MX SEM 1.jpg
    78.4 KB
Taffy said:
I don't know Avi.? I don't know what that stator looks like. the thing to remember about an FC stator is that it is so thin it doesn't get into the middle of the flywheel. It might not be the stators fault though because despite what I just said, the next thing to remember is that the flywheel isn't very tall either!

...it doesn't come out from the crankcases so far! I have a brand new FC flywheel here and used FE flywheels with which I could take a photo.

I attach a photo of a very thin FC stator....

now i've shown you mine you can show me yours! ;);)

regards

Taffy
Click to expand...

hi Taffy
i have to fix my friend 470 2001
its not runing ,
i checked the valve clearence , 01mm ex and in
im trying to check copression but i got low reading 30 psi with the cikstart im not strong guy so maybe this is the reason,what read should i get?
im sending a photos of the stator ,im not sure what is the right position of the stator inside the cover please help me.:(
 

Attachments

  • DSCF6596.jpg
    DSCF6596.jpg
    82.4 KB
Taffy said:
I don't know Avi.? I don't know what that stator looks like. the thing to remember about an FC stator is that it is so thin it doesn't get into the middle of the flywheel. It might not be the stators fault though because despite what I just said, the next thing to remember is that the flywheel isn't very tall either!

...it doesn't come out from the crankcases so far! I have a brand new FC flywheel here and used FE flywheels with which I could take a photo.

I attach a photo of a very thin FC stator....

now i've shown you mine you can show me yours! ;);)

regards

Taffy
Click to expand...
here is some fhotos
DSCF6595.jpg

DSCF6593.jpg
 
well basically that is a FE stator inside an FE flywheel so you don't have a problem.

not the greatest angle for a photo but i'm [pretty sure that that's a deep flywheel.

Taffy
 
Taffy said:
well basically that is a FE stator inside an FE flywheel so you don't have a problem.

not the greatest angle for a photo but i'm [pretty sure that that's a deep flywheel.

Taffy
Click to expand...

what will be the right position of the stator inside the cover? there is no indicators at all
 
Taffy,

Do you have the stator spacer for the FC’s ?

I was looking at ordering one, but your store says no longer available or something....
 
yes I have one Vor, would you email me please? I accept emails, calls, FB, skype but I can't patrol twitter and every web site. I'm an email hugger. Oh and I forgot texts. and mobile calls.

Avi; yes, I do. you too should email me.

cheers

Taffy
 

Similar threads

G
2001 Fe501 - No Spark
Replies
3
Views
485
Taffy
Taffy
R
Dead flywheel?
2
Replies
31
Views
2K
Robzerg
R
S
New stator from China
Replies
5
Views
781
Sweden470
S
I
Aprilia AF1 stator / pre-99 Husaberg FE
Replies
1
Views
548
Taffy
Taffy
G
CARBURETION ADJUSTMENT PROBLEMS FE 450 2005
Replies
0
Views
52
GMC77
G

Register CTA

Register on Husaberg Forum! This sidebar will go away, and you will see fewer ads.

Recent Discussions

Recent Discussions

Back
Top