Fitting a used TRX450 exhaust to the Berg 550 (pics inside)

Husaberg

Help Support Husaberg:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
B

ballbag

Joined
Feb 7, 2012
Messages
20
My 1st topic :!:
Bought this pipe off our local forum last week:
http://www.wilddog.za.net/forum/index.php?topic=95707.0
LeoVince.jpg


Googling the exhaust, it was evident that unlike a normal slip-on, the header pipe slides into the silencer, as opposed to the slip-on, slipping onto the header pipes.
Like so:
1-1.jpg


Standard TRX450 pipe removed:
2.jpg


Notice how the standard exhaust slips over the 50mm pipe:
3.jpg


..and how the header pipe slides into the vince:
4.jpg


The adjustable clamp makes for easy fastening to the frame:
5.jpg


Looking mean:
11042012984Copy.jpg

6.jpg


I will have to change my jetting, and haul a couple of extra jocks. The 550 will rip moar >:D
7.jpg


I gave it some fresh exhaust packing too (notice the red silicon)
 
Re: Fitting a used TRX450 exhaust to the Berg 550 (pics insi

I will say it does look trick....the only downside will be the lead pipe or header pipe goes around the start of the can which will be a leak point usually even if the pipes fit tight. if they are a nice tight fit though it might be minimal or nil being as its back that far and with a free flowing can; testing will tell. on a loose joint like this, as long as the pipe closer to the engine goes into the trailing pipe and fits tight it wont leak. if its clamped it wont leak either way but looks ugle and may not come apart without destroying it depending on the style of clamp used. if it did leak excessivly you can always cut a small slot lengthwise down the pipe an inch in or so from the end and put a cv boot style clamp or equivalent on it and still look fine and come apart, once you cut the clamp off of course....let us know how it works out.... :cheers:
 
Re: Fitting a used TRX450 exhaust to the Berg 550 (pics insi

Perhaps I'm not understanding you correctly..
To clarify, the vince pipe has exactly the same connection to the exhaust as the stock silencer, only, it sits on the inside. I.e. 3cm long, 50mm connecting pipe inside the vince.

This means it has the same sealing capacity as the stock unit. I gave it some high temp silicon on the connection for good measure.
 

Attachments

  • 22.jpg
    22.jpg
    35.9 KB
Re: Fitting a used TRX450 exhaust to the Berg 550 (pics insi

I thought you said on the factory connection the headpipe goes into the can with the new setup the headpipe goes around the start of can. as a general note reguarding exhaust systems, the pipes are less likely to leak if the front pipe goes inside of the following pipe, for example if you have three pipes on a system the back end of the first pipe will go inside the start of the second pipe and the end of the second pipe will go inside the start of the 3rd pipe. do you understand or is it still me that is confused? :D
 
Re: Fitting a used TRX450 exhaust to the Berg 550 (pics insi

:lol: You are still confused yes.

Bottom line; the Leo Vince is a perfect fit with no leaks 8)
 
Re: Fitting a used TRX450 exhaust to the Berg 550 (pics insi

great! you can forget all i said then except that it looks trick! hopefully it performs equally as well for you! :cheers:
 
Re: Fitting a used TRX450 exhaust to the Berg 550 (pics insi

Thanks :mrgreen:
My jetting is a mess at the moment but hopefully I'll have it running 100% in no time
 

Register CTA

Register on Husaberg Forum! This sidebar will go away, and you will see fewer ads.

Recent Discussions

Recent Discussions

Back
Top