work

Just wondering if anyone has fitted an akropovic muffler for an fe570 on an fe450 will it fit...? Thanks in advance, Guy Sent from my iPhone using Tapatalk

I notice on my 04 Fe 450 it don't have the controls for the high-low beam and signals do I need those controles for the light to work or should it still work without the left side switches ? My light is hooked up it doesn't seem to turn on tho. The previous owner removed just the signals and...

For my 95 FE350 and 99 FC 501. I noticed these bikes do not have a lower chain roller. The parts book shows what looks like a wear pad in place of a roller, the book calls it frame protection. I can see on the frame where it would go, Anyone know if you can still get these? Taffy, your thoughts?

My ignition rotor (flywheel) doesn't want to move. I didn't have the puller, so I bought the Motion Pro, it has the nose cup for the crank tip. I can't use a torch, the magnets are glued in place. I haven't tried an impact yet. I put some thin lubricant on the fit and loaded the puller tight...

I can't afford a new Beringer disc so purchased an EBC but even though I have adjusted the sensor for the speedo, it still won't pick up the speed. Any help would be much appreciated

Hey I have an FE550 and the starter was working fine, albeit the sprague clutch was well worn out... I cranked it a heap in the shed the other night and the battery ran down a fair bit but it eventually started Now it's fully dead, the starter will not click or turn over at all. I have...

i am ashamed to admit my 02 470 only has about 100 hrs est.....and believe it or not it's never been apart and it still starts and runs good. when i bought it i also got updated rocker arms and an updated dual bearing counter balancer. however I never installed them. anyway i am going to...

Hi all, I'm heading to Vegas from Australia with about 11000 of my closest friends from work at the end of August for a conference :) Quite a few of us ride, and I was wondering if anyone could suggest some good tours we could jump on? Given we are travelling from OS we will obviously need to...

I was wondering if this gpr ktm stabilizer on my newly aquired 06 sx 250 will fit my 08 fe 550? I cant tell ya how much I love this ol berg.

2005 FE650e currently in SM trim 90 hours The other day I switched rocker arms as the intake bearing was sloppy. I used rockers from the engine im not using at this time. Adjusted valves and ran it a bit then changed the oil. Noticed a little timing chain noise, so checked the tensioner. Only...

Hey guys! im Norwegian, and new in here. just bought myself a 2003 Husaberg FE650 and have got some electrical issues. the seller told me the only reason the el-start didn't work was because the battery was flat. (oldest trick in the book) but, changed the battery. and the electrical starter...

So I'm getting a 2011 570 S and I was thinking about making a spare fuel tank out of the stock exhaust and mounting it on the left side of the bike. Figure it might hold a gallon and would look like the bike has dual exhausts. I'd make it so that you could pull it out and fill the gas tank...

Hey guys, new rider here (Canadian living in Iceland) with a 2008 fe450 having lots of trouble finding a replacement lever for the front brake... Long story that starts with me ordering from http://www.midwestme.com/pages/product.html thinking it would work. turns out this lever does not...

Hi there, I am new to this forum, I just purchased a 2011 Husaberg FE 570 S and I need to do the initial first hour valve clearance inspection as per the owners manual recommendation. The problem is I don't have a service manual and the dealer I bought the bike from has to special order it and...

I have a problem on my 2007 FS 650. The idle is a bit low. When turning the idle screw nothing happens!! The idle does not change. Any explanation ?? Thanks Ragnar

hi! today i started my bike and went to ride but there was a problem, only gears 1-3 worked and it was hard to get 3rd gear on. Yesterday i noticed that gearlever was working kind of strange, it suddenly changed the gear and i wasnt doing anything. Atm, the lever is jamming and working very...

who in the usa is doing performance work on the fs570 engines? thx, rm

While at Home depot I ran across some Foam Pipe Insulation and figured why not use those to keep my pants from constantly melting when touching the side pipes. I thought of putting a layer of Parchment Paper to prevent the foam from sticking to the pipe but I'm not sure it'll help cause the...

I just bought a KTM switch for my '09 FE570. The switch includes a blue horn button, high beam, lowbeam and red engine kill button. It plugs straight into the factory harness and works great except the kill swith doesn't work. I was hoping I could remove the stock engine kill switch and replace...

i have a 99 fe501 are there any street/supermoto tires that fit the stock rims, my tires say not for highway use. what size tire work on my bike? any suggestions of brands models? thanks.