tube

Pretty in Stainless innit! I've had a few made; they'll be 15 quid each (plus in the EU). regards Taffy

Hi, Working on a little modification - and am trying to ascertain the inner diameter of the steering tube. My ID caliper arms can't clear the flared steering bearing races to effectively measure against the INNER walls of the head tube. Since the OD is 56mm, and I'm guessing a wall...

I am looking for used, but in good condition interim tube ideally with muffler which fit together. I have to replace some homekit made by previous owner and it is pain :( https://ctrlv.cz/s336 or https://ctrlv.cz/1jZu Thanks for any tips ... browse ebay and nothing :(

I am looking for used, but in good condition interim tube ideally with muffler which fit together. I have to replace some homekit made by previous owner and it is pain :( https://ctrlv.cz/s336 or https://ctrlv.cz/1jZu Thanks for any tips ... browse ebay and nothing :(

Did all the fuel pump mods on my 2010FE 570 and went out on my first ride this past weekend. Worked Great. Stopped to take a rest in the middle of a long ride and decided to check my fuel. Opened the cap and fuel game gushing/FLYING out like a geyser. Very dangerous situation with a hot bike...

Has anyone fitted a canister/tool tube to there bike? I was thinking of getting one and mounting on the side under the plastics opposite the exhaust and using it to store some emergency fuel in a fuel bottle. If you don't know what a tool tube is have a look here ToolTube

So I'm a suspension noob, and while trying to change my fork springs, the shock rod sank into the tube and I didn't have anything long enough to grab it. I finally decided I could just remove the front tire and compress the fork all the way and grab the shock rod. This worked great, until it...

Hello I haven't a husaberg bike but i'm using wp extreme 5060 for a fork swap to a dr 650. So i hope to find some good tips from u. I have the official technical wp 5060 manual. My problem is i can't separate the inner from the outer tube. I heated the outer with a torch (exactly...

Hi, quick question, searched and couldn't find an answer. I Have a 2012 FE390 the rear's fitted with a 140/80 with an 18" x 2.15" rim I recently purchased a Ultra Heavy Duty tube for the rear but the tube has 110/100D - 18" written on it. Will it still fit? do they make tubes 140? or is it...

I got a pretty nasty ding on the bottom of my fork tube where the dust seal is that I'm sure is causing a leak. My guess where the oils seal goes is probably a little warped also. Replacing the seals probably wont be enough, I'm going to see if I can get it repaired. If I can't get it...

FCR carb overflow tubing what size ID should it be?

[youtube:yququzp4]http://www.youtube.com/watch?v=reU5mbT90N0[/youtube:yququzp4] covert-youtube-viewiness-moderatorin'

Hello friends again: I am starting race season here in my country (Ecuador) and this is the second year using my FE450 `09 I use maxxis extra heavy duty tubes for enduro riding and they´ve work whell (no flat tires), buy I was wondering that if for the race season it will be better to use the...

Nobody had heard of a radial tube when I went to the local bikeshop... I ordered the only radial tubes I could find, Bridgestone, but still curious as to the difference. Anyone? :bounce: Thanks, DB

I need to replace my throttle cable, including the 'tube bend' on my '03 FE400. Is the cable and / or the tube a common part with any KTM model? If so where do I get the part number cross reference? Getting parts for my Berg is a nightmare in the Toronto area!

Can we get an alloy throttle tube for the pre 09 Husabergs ? Haven't found one. I see they are available for 09 though. pollo

Can any body tell me if the down tube on the frame shoud be straight, on the FE550 (04) that I have bought the down tube apears to be slightly bent in an out would direction in turn the back of the front mudguard is rubbing on the down tube. Allso the collector exhuast box is rubbing on the top...

Anyone catch the Italian round of the World Supermoto Championship on Speed TV last night? They did a cool feature on the Husaberg "factory" effort. Don't want to spoil race results for those of you who may have Tee-Vo'd it. Every time I watch guys like VDB do their thing it makes me consider...

Been looking through the site and can't find torque spec for triple clamp to fork tube. I'm sure it can't be much, but would appreciate Husaberg recomendation if anyone has a source. Can't find it in repair manual or fork repair manual. Please express it 'Foot-pounds". Bike is 97' FE600E...