temp

What is the maximum rev that you shouldn't go over on those engines? Mine is a 1994 600cc with no oil pump. And what temperature is dangerously high? Otherwise, just got the bike running and it's finally easy to start hot and cold. Just installed a trail tech speedo/tach, horn, brake...

Cheap,waterproof,accurate and easy to install,hope it lasts under the Greek sun. Top Gauge Digital Motorcycle MotoBike Oil temp Gauge Meter RED LED Waterproof | eBay A local machine shop made for me a T adapter for about 20$ to connect the temp sensor on the 20mm coolant hose above the...

Hi peeps first post on here, I have a 2003 650 that I have fitted a Vapour Trailtech speedo kit to, I have fitted the capacitive Rev sensor and would like to know the Max Safe revs under load for changing gear, I also fitted the liquid temp adapter in the rad hose coming off the water pump as I...

My fan stop working on my 10 fe570 and found the temp switch was bad. I replaced it with a replacement BMW one and it failed after two rides. Is this just a coincidence?

Hi I have just bought a trailtech Vapor speedo kit, I was just wondering what side you would recommend installing the temp sensor for the radiator, I have read people placing it on the left side and also the right. I have also bought a radiator fan kit and was wondering if that would interfear...

Hi I have a 2001 501 fitted in a crosskart, fitted an el-cheappo temp gauge and it shows 100 C. The radiator does not feel extremly hot + it does not boil over. Am I correct to the gauge is suspect? Thanks for input :angry:

Hi! Doesn anyone know how the coolant temp sensor "works"? Temperature / Resistance (curve) ? :) Thanks! Regards

I have a 2010 FE390 which is a dream, absolutely loving it, every aspect. it's my first ever 4 stroke after years on small bore 2 strokes. As a precaution; and the fact I had to replace the standard instrument panel after getting taken out and hitting a tree i have installed a Trailtech vapor...

Hi guys I have a overheating problem with my FE 390, I have taken it to the dealer several times and we cant seem to figure it out. I have installed a fan kit, replace the coolant with ICE, change the fan sensors, removed the thermostat. I purchased a FMF slip and had to work the jetting. I ride...

The green female end of my my water temp sensor came off and melted on the header pipe. This connection is just to the left of the spark plug on the right side of the motor. The clip has a stamp with "AMP 10737 11082" on it and is part of the wiring harness of the bike, so I can't buy just the...

I found some links by LeFrog I believe. Anyone done this with sucsess? Part numbers for the switch as it is a 1/8" NPT thread? This looks like the cleanest fix if you don't have a threaded radiator plug,( pre 06?). http://www.egauges.com/vdo_acce.asp?Subgroup=Hose_Adaptors...

Looking to find best location for temp sensor (in hose type) for my fs650. I was thinking the short hose coming off cylinder to top of radiator. Any one put one on there bike before? Will post pic's of alloy dash set up with Vapor on it soon. Thanks Glenn

Hi All The temp switch that came with my cooling fan is rated at 85 deg c cut in and 80 deg c cut out, basically the fan runs most of the time, I have read that a lot of people install a separate switch, I do not want to do this, so was wondering if any of you have sourced a higher rated temp...

Well finally got around to finishing up a couple of home made temp controllers for the grip heater elements. It uses a 555 timer and power mosfet to control the heat using pulse width modulation. Temperature is controlled using a dial pot. It is based on a design I found on the net. Seems to...

What would be the best spot to put a Selco temp switch that closes at 190F and opens at 160F, in a DIY fan configuration? I was thinking about putting one by the inlet (where the coolant arrives from the pump). But at that position, would the temperature rarely go under 160F? I could also...