tdc

Replacing the cam shaft bearings on my 350. Anyone have any tips on location TDC I don't see any marks on the flywheel Thanks

Hey just wondering if anyone could give me some info on getting the motor to top dead Center to adjust the valves. This is my first time checking valves so any info would be greatly appreciated. I got rad and valve covers off now just need to figure out how to properly get TDC?? My bike is a...

Just want to check I'm doing it right... cheers folks. https://photos.app.goo.gl/R6GUtHbTreUmUq2l2

Hi all, following on from my previous thread about the snapped tappet. I have now got two new exhaust valves, new stem seals, water pump seals and other bits, the valves are lapped in and head is back on. All seems to be in order. Now I am trying to get the cams and crank timed up. I...

Also known here as Dr. C If you haven't seen his videos they are quite interesting. This video shows how to use a degree wheel and the dead stop method of finding TDC as applied to cam timing. https://youtu.be/q-gn8S3ydFs

Anyone with a good way to find TDC on my '13 FE350? Has a Rekluse, no kickstarter. In the past, I've used the kickstarter on other bike to cycle the engine until TDC was found. Rear wheel spins withthe Kluse :cheers:

How do I make sure that I have the correct TDC before reinstalling my cam :oops: Cheers

Hello, I finally got tired of being too lazy to pull the side cover and check TDC correctly. So that's what I did. And took a quote from Taffy that he said. " Staple at 5 oclock then bring to 9 oclock with edge of staple in line with edge of cover screw hole" Ok, so I wanted to see how close I...

How far from the top of the barrel do your piston's stop at TDC ? mine is about 1.8 mm from the top. is that common? Regards

I thought I'd share a little mod I did to the ignition cover which makes it real simple to find TDC for checking valves. And with a Rekluse you can't turn the crank over with the rear wheel, and it's easy to damage the ignition cover gasket if you remove it to turn it directly. Most Japanese...

Hi Iam about to fit one of the Dirt Tricks cam chain tensioners to my 570 and reading the instructions for fitment it says about putting the engine on top dead centre for some models, and to check if this is the case for your bike before fitting, I have used the search function to see what...

Hi. Valve Shims needs to be changed, to some smaler ones. Where do i take out a screw, an insert the engine blocking screw ptn 0113080802 in the part manual. Sinse I need to take out the cam. Sorry for bad english. Regs Burud

here is an easy way to find tdc to check valve adjustments put bike on a stand take off tank and valve covers now take out spark plug get a coat hanger and straighten it out put bike in gear, now poke the wire hanger into the plug hole till it hits piston, now roll rear wheel and the wire will...

I'm replacing the timing chain on my 02 FE501 and I'm alittle confused as to were the cam lobes should be at TDC while hooking up the new chain. I've seen some cases where people have said to have the lobes facing up at 11 and 1 o'clock. I've also heard people say that the lobes should be facing...

http://www.husaberg.org/wiki/index.php/ ... arks_wrong well, no excuses now you numpties! go find TDC and sort this out - FOR GOOD! regards Taffy

I have a small question about the TDC. I had a KTM 625 and it had a small stud that you removed, pulled the washer and reinstalled it in a small notch in the crank, this would would lock the crank at TDC. There is a similar screw my 04 450, is this used for the same purpose. :?:

i have been reading all the posts on finding the true tdc on your engine but they dont exsplain the dead stop method can some one help.i think this is why mine is dificult to start. i have fitted new plug all new jetts in the carb and still it wont start. im getting a few kick backs.and today i...

hi, i am trying to set my timing and i need a dial indicator for TDC. got any leads for an inexpensive tool? thanks tuts

hey guys, i know this has been proberbly answered before but im in need of help! when you guys adjust the valves (i have 2005 fe450e) do you guys remove the rocker cover? i have trouble getting feeler guages in little covers? also can someone please explain the best procedure to find top dead...

:oops: I fell stupid asking this for some reason. But here goes.. I noticed on the front of my motor (04FE550) there is a screw (plug) that covers a hole where a screw could be inserted to hold the crank in place at TDC?. The question is: Can you pull the plug and insert a screw long enough...