steering

Hi! Been searching to find the correct STEERING STEM BEARING & SEAL KIT for my Husaberg FS 650 2008. i have searched and found ALL BALLS STEERING STEM BEARING & SEAL KIT - part number 22-1032 , but previously I have swapped with a Husqvarna 701 SM, which had part number 22-1026 . I can...

Currently on my 09 FE570. Works great with no problems. $300

Can any of you gents tell me what one of these is worth? I don't want to sell it, just establish value. (I already know It's worth what someone will pay, Ebay etc);) Thanks!

Hi, Working on a little modification - and am trying to ascertain the inner diameter of the steering tube. My ID caliper arms can't clear the flared steering bearing races to effectively measure against the INNER walls of the head tube. Since the OD is 56mm, and I'm guessing a wall...

Hi guys has anyone fitted steering damper to there bike and noticeable seen an improvement specially at speed ???? .i do get a bit of steering shake at speeds Sent from my iPad using Tapatalk

Hello husabergers, I have recently gotten my triple clamp powdercoated, and i am now having issues installing that damn steering stem again! It was a mess to remove, i used heat and a hammer and some hard knocks. My triple clamp is the adjustable one with either 16 or 22mm offset, but it...

Having to change steering bearings due to them being notchy, drop the yokes out today and bottom bearings rusty. After a lot of f..kin about I got the bottom bearing off, there is a washer under the bottom bearing. Having checked the All Balls kit I have there is no washer just bearings, cups...

Please let me know if you have a Scots Sub-Mount Steering Stabilizer for 2011 Husa 390 FE for sale. I'm only interested in the Sub-Mount! Thank you.

Hi all! It's been a while since I've asked a question on my 2010 FE450 but here's the story... I rode a 550 mile dual sport through SD last week and all through it I could hardly turn the bike, it wanted to go straight and gave me a very unplanted loose feel when turning. So after looking at...

I can buy a kit with Part# 1256550037 for a good price it's listed for husaberg te 250 2012.... (gpr v4 fat bar stabilizer kit) I am almost sure it would be the same kit /triple clamps on my 570 but want to be sure before buying it and than I could have a steeringdamper I can't mount on my...

Hi, does anyone know if the steering head bracket for the pivot post for an RFS ktm steering damper fit or can be easily made to on a 07 FE650? I have a Scotts damper, and need to get an under bar mount. I can get a cheap ktm mount set up, just don't know if it will fit. I believe the FE may...

I have a nearly new Scotts Bolt On Damper that came off my 08 FE550. It is the traditional mount - NOT SUB MOUNT. Like new condition. $275 US srocher at Stratfordhomes dot ca

Can anyone give me value for bottom screw? Top one is 10nm? Are there any difference beetween them - in part catalogue they have got same size but one is marked "SL" and they have got different part numbers.

I am looking for a scotts steering damper for my fs570 but the price is a bit steep if I have to pay the full amount of import taxes/shipping etc form th us anyone knwo where to get them for decent price in uk/europe or wants to sell theirs to me;) I only paid half the amount for my (new lsl)...

Hi Had a accident when i was pulled over suddenly had to brake and resulted in understeering and falled at about 20-30km/h, afterwards the steering feels very strange and unstable. *The handlebar was a tiny bit bent, bent it back *The handlebar/fork was also not syncronized completely...

hello ! :) i am about to send my frame to powdercoating so the bike are in pices. but i get the steering head of the bike? do the front shocks need to come of ? am i dooing it allt wrong ? :oops: first time :mrgreen: regards daniel

Looking for a steering stem top nut to fit my 97 fe501e. The nut that holds the top triple clamp down. It was missing when I got the bike.

I was wondering if this gpr ktm stabilizer on my newly aquired 06 sx 250 will fit my 08 fe 550? I cant tell ya how much I love this ol berg.

Hi all, I've talked to a guy who is going to sell his steering dampner off his 2011 KTM 250 SXF and am would like to buy it. But...will it fit? After hearing stories of mounts that cross fit and tales of "needing the specific mount" I'm a little confused and cautious. The model he's selling is...

Hey guys, I need to replace the steering head bearings on my 99 501. I was wondering if anyone had a bearing number i could bring to the local bearing supply shop.