specs

Looking at getting my -02 FE650 registered after finally getting everything (almost everything) running. I’ve been looking for the specifications for the brake rotors for my bike, and it’s hard to find! My rotors are 4mm thick where there is no wear (so 4mm brand new?), and 3.3mm thick where the...

Hey everyone just wondering if anyone knows the torque specs for the case halfs on a fe 450 ?? I just purchased a 04 husaberg 450fe and notice the bolts were quiet loose. Are these bikes known for nuts and bolts coming loose?? Anything alts I should check to make sure it’s torqued to specs...

Moved to electrical....

What are the torque specs for an 08 650 on the clutch main bolt and the pressure plate screws? Thanks

Hey Everyone, I was on here a long time ago when I owned a 2003 501 FE. Now I'm back and just bought a '10 390 FE! Rode it once and really liked it! It has 242 hrs on it and decided to tear down top end. Def had an issue with cam follower bearing but besides that I'm looking for the specs for...

Is my 2005 650 supermoto made with a 5" rear rim from the factory or has the Former owner replaced the standard rim? I have trouble with Chain rubbing my 160/60 rear tyre and rim. Can you recommend a narrow sport tire for use on public roads size 160/60? Can i fit a 150/60 on a 5" rim or is...

Does anyone have the specs for the older 96 or so camshafts? I building an older Berg out of some salvage bikes that I have. Need to know about the difference between the A and B and C cams and in which models they were used in. Saving my $ for a newer Kvarnaberg.

anyone got the specs for the early jetting written anywhere? all I can see in the first couple of owner's and part books are the individual part numbers and not what the specs are. regards Taffy

I looked high and low but cannot find a test method and spec. I can assume it is a resistance test, but how many ohms under wet and dry condition? Mine tests out at ~825,000ohms, wet or dry, at connector and at the device itself, so I'm pretty sure it's a dead duck. FYI: The shrink-tubing on...

any body know what the head nuts and the allen bolts that hold the jujg to the cylinder head need torqued down to ?

Cant find any HP and Torque specs for FE390 on google. Anybody have any HP and\or torque specs for the FE390? Regards Fizz

How much fork oil should I be putting in my '07 FE650? For some reason the manuals do not say :?: Can anybody point me in the right direction? cheers

I have a 2007 Fe 450 ‘works Replica’.I trying to get details on the front forks: shim stacks and spacers but my ignorance on the status on the ‘Works Replica’ model is holding me back.Is it a stand alone model with some different specs or just a comemerative standard...

I'll be ressurecting a 1994 fe600. It came without a stator, for which I've found a replacement from a 1996 fe501e. What's the correct procedure for testing the stator (other than putting it on the bike, and see if it'll run ;))? What is a good timing mark to line it up with? I'd like to...

CAN ANYONE HELP ME WITH THE PROPER JETTING FOR A'06 FE 650 AT SEA LEVEL? THANKS DAVE

Hello all, I know that 2004 cam is about 266degrees duration and about 10,82lift+I have also the X2 cam with his 272 degrees duration. has any body has the specs from a 2005 -2006-2007cam??? Thanks Madero

Hello, fellow Berg freaks. Doctorcorey here. Well, I just got my 91 501 back together. It felt good to have my favorite horse back under my butt! Anyhow, I'm due to service the forks now, and I've either lost or forgotten the specs for the fork oil type and level. I mainly use my bike for...

I would really appreciate if any owners of the 04/05 bikes could advise me what their owners manual recommends as replacement times for the counter balancer bearings, counter balancer intermediate shaft bearings and rocker arms. I wish to compare these to the 02 recommendation of 50 hour...

Anyone know the torque specs for a 2002 husaberg fe400e head? not the main sleeve thing, but for the 7 bolts on the head.